the construction services

Agency:	Glades County
State:	Florida
Type of Government:	State & Local
NAICS Category:	236220 - Commercial and Institutional Building Construction
Posted Date:	Jun 11, 2026
Due Date:	Jul 6, 2026
Solicitation No:	Request for Proposal RFP #2026 - Rehab-Eagle,D
Original Source:	Please Login to View Page
Contact information:	Please Login to View Page
Bid Documents:	Please Login to View Page

Attachment Preview

Glades County

Housing Rehabilitation Program

Work Write-up/Bid Form

Name: ____________________________________

Address: ___________________________________

Phone: __________________

Project #: 2026-Rehab-Eagle, D

This bid sheet must accompany the proposal. Any alterations or changes to this document will deem

that bid unresponsive and will no longer be given further consideration.

Sealed bids will be received until 4:30 P.M., on July 6, 2026, at the Glades County Community

Development 198 Sixth Street SW, Moore Haven, FL 33471 and opened immediately thereafter at the

same address. The work to be performed at the property identified below, includes furnishing all labor,

materials, supplies, tools, equipment and services required and necessary to perform and complete the

construction work described herein and more specifically identified in the attached Rehabilitation

Specifications Analysis Report. Said work to be done strictly in accord with GCCD's rehabilitation

policies and procedures. The construction work will be performed at the property owned by and

located at

Property Owner(s): Don Eagle

Property Address: 300 5th Street NW, Moore Haven, FL 33471

THE WORK WRITE-UP/BID FORM IS A GENERAL OUTLINE OF THE WORK TO BE PERFORMED. PLEASE

REFER TO THE PROJECT SPECIFICATION BOOKLET FOR DETAILED INSTRUCTION FOR EACH ITEM NOTED

BELOW. Do not include labor amount per item in your figures below, Labor is now a separate item. Also,

when you are able to indicate the name of the product and or manufacturer, such as air conditioner,

Rheem or Goodman.

Item Description

Price Estimate

1. MASTER BATH - BATHTUB SHOWER CONVERSION ADA COMPLIANT ROLL

IN SHOWER

Install a glazed porcelain bath set comprised of a tub soap dish, 24" towel

bar. Owner's choice of stock color.

2. MASTER BATH – BLOCKING FOR GRAB BARS

Install Grab Bars for tub/shower area for framed walls using min. 2"x6"

pressure treated blocking or 1/2" plywood and for CMU walls using min.

1"x6" pressure treated wood blocking at desired height to meet

accessibility requirements.

Furnish and install grab bars withing the tub/shower area per the current

Florida Building Code. Horizontal and vertical grab bars shall be installed

per the Building Code of Jurisdiction. Each grab bar shall be of proper

length and located in the proper positions as determined by the Building

Code of Jurisdiction. All bars shall be round with a minimum of 1.25"

diameter, maximum 2" diameter, type 304, 18 gauge (.049), brushed satin

stainless steel, with round snap on covers and welded 3" flanges and a 1.5"

space between the bar and wall. Bars must be fastened securely to the

wall framing.

Page 13 of 27

Revised 05/27/2025

3. MASTER BATH WALL TILE - SHOWER SURROUND

Remove existing shower tile, tile backer, pan and water damaged wall

materials affected by framing of the new shower. Replace damaged

studs and furring strips. Shower pan to be installed per Spec 5425.

Install wall tile of 12"x24"x1/4" polished porcelain wall tile or approved

equivalent to ceiling over 1/2"-5/8" cement tile backer board equal to

Wonder board, or Hardie Backer board, or Dens Shield, or approved

equivalent. Place wood backing/blocking per Spec 5414 for handicap

bars. Install a new washer less single handle diverter assembly faucet

valve with screwdriver stops, American Standard "Town Square" or

approved equivalent. Max. 2.0 gpm water saving shower head. Include

preformed base, cap, stop, return, and trimmer pieces to complete

installation up to ceiling height. After at least 24 hours drying time, apply

Spectra LOCK® PRO Grout. Clean floor and apply mildew resistant white

Low VOC silicone caulk to all edge seams and pipe penetrations. Wall

tile allowance $2.50/sq/ft. Ceramic Tile Baseboard. Install a Ceramic Tile

Baseboard using same size as floor tile and cut into 4" to 6" wide strips

over a sound surface with troweled adhesive. After at least 24 hours

drying time, apply latex based Portland cement grout. Clean all excess

grout and apply mildew resistant white silicone caulk at all seams. PREP

& PAINT ROOM w/ PAINTED TRIM-LOW VOC Using lead safe work

practices remove & dispose of all loose material & dust prior to

installation of new materials. All cracked or loose plaster is to be

repaired with a bedding coat of Durabond & fiberglass mesh tape. If

plaster & lath boards are loose, resecure or remove & replace it with

drywall patch. Sanding of any surfaces contacting or adjoining a lead-

based painted surface shall be done with appropriate procedures such

as using a HEPA filtered sanding vacuum or a wet sanding method.

Prime as necessary to seal stains, raw plaster, etc. Paint ceilings two

coats in flat ceiling white & walls in eggshell or satin finish cut-in neatly

to trim & at all corners & edges. Prep trim doors and windows by de-

glossing painted trim prior to painting and prep all doors to be painted.

Apply two coats of latex semi-gloss paint to cover completely &

uniformly. Colors are the choice of the owner from stock colors.

Maximum of 2 color choices for interior. All paints and primers must not

exceed the following maximum VOC requirements: Flats 50 g/L; Non-

flats 50 g/L; Floor 100 g/L; Anti-corrosive 250 g/L. All adhesives must

comply with Rule 1168 of the South Coast Air Quality Management

District.www.aqmd.gov/rules/reg/reg11/r1168.pdf All caulks and

sealants must comply with Regulation 8, Rule 51, of the Bay Area Air

Quality Management District (BAAQMD).

4. MASTER BATH - HANDHELD SHOWER DIVERTER W/ ADJUSTABLE RAIL

Install a new washer less single handle diverter handheld assembly faucet

valve with screwdriver stops, Moen "Chateau" or equal.

5. IMPACT WINDOW

A. GENERAL INFORMATION

1. Replace windows with new single hung aluminum or Vinyl impact

windows that meet the current Florida Building Code and current

applicable code requirements for product approval. All provided

windows must meet the required wind rating. All existing openings to be

Page 14 of 27

Revised 05/27/2025

examined for attachment requirements per manufacturer's

requirements and Building Code of Jurisdiction. New windows are to be

of similar size to existing windows. ALL FENESTRATION MUST COMPLY

WITH THE FLORIDA ENERGY CODE.

B. PROJECT CONDITIONS

1. Remove and dispose of all existing windows to be replaced; clear

room and/or cover all surfaces prior to beginning work; remove and

dispose of properly including: all damaged drywall, insulation, and

framing. Where security system wiring exists, the Contractor shall

preserve the security system as it pertains to the windows. This may

include replacing contacts and repairing the security system circuitry

affected by replacing the windows.

C. PRODUCTS

1. Impact Windows to be PGT, CGI, or approved equal, single hung

aluminum or Vinyl windows with insect screens.

2. All Bathroom windows to be obscure glass.

3. Color selection may be limited due to supply availability and/or time

constraints required to complete the construction.

D. INSTALLATION

1. Install all windows per manufacturer's requirements, NOAs, and

Building Code of Jurisdiction and form a watertight installation with drip

at head. Seal all joints.

Repair all exterior/interior damage to match existing as best as possible. $

6. HOT WATER HEATER RELOCATE TO EXTERIOR

A. Provide all labor, materials, equipment, permits, inspections, and

incidentals necessary to disconnect, remove, relocate, and reinstall

the existing domestic hot water heater from its current interior

location to an approved exterior location, in full compliance with

applicable Florida Building Code (FBC), Florida Plumbing Code (FPC),

Florida Fuel Gas Code (if applicable), Florida Mechanical Code,

Florida Energy Conservation Code, and NEC requirements.

B. Safely remove existing unit without damage to surrounding walls,

floors, or finishes.

C. Cap all abandoned plumbing, gas, and electrical connections in

accordance with applicable code.

D. Patch and restore interior finishes as required to maintain habitable

condition.

E. Install the water heater at an approved exterior location compliant

with: FPC Section 504 FBC Chapter 3 (Protection of openings and

building envelope). Water heater shall be :

1. Installed on a rated exterior concrete pad or elevated corrosion-

resistant stand Properly anchored for wind load resistance per

FBC Residential Chapter 3A minimum of 1 inch above grade (or

as required by manufacturer)Clearance requirements shall

comply with: Manufacturer’s installation instructions FPC Section

504.3Provide an exterior-rated.

2. Insulated water heater enclosure, or listed water heater rated

for outdoor installation. Tank, piping, and fasteners shall be

corrosion-resistant or protected against weather exposure per

FBC Section 305.All penetrations through exterior walls shall be

Page 15 of 27

Revised 05/27/2025

sealed watertight with approved materials.

3. Reconnect cold and hot water piping with approved piping

materials per FPC Chapter 6Dielectric unions where dissimilar

metals are used.

4. Install a shutoff valve on the cold-water supply line per FPC

Section606.2.

5. Install a temperature and pressure relief valve with discharge

piping: Same diameter as valve outlet Terminating 6–24 inches

above grade No threaded end Compliant with FPC Section 504.6.

6. Insulate exposed hot water piping per Florida Energy

Conservation Code requirements.

7. LABOR AND PERMIT

8. TOTAL BID:

Page 16 of 27

Revised 05/27/2025

Glades County SHIP Work Write-up

THIS PAGE MUST BE INCLUDED WITH THE BID FOR IT TO BE VALID

Work is to be performed in a workmanlike manner, in accordance with the Standard Rehabilitation Specifications,

local codes and manufactured specifications.

The contractor shall be responsible for repairs and/or reinstallations of materials/equipment/fixtures damaged or

removed due to any work item contained herein.

Contractors shall properly dispose of all fixture, materials and other items removed from the dwelling unless

otherwise specified herein.

ALL ITEMS MUST BE COST ITEMIZED IN THE SPACE PROVIDED OR THE BID WILL BE REJECTED. ALL ADDENDUMS

MUST BE SIGNED AND SUBMITTED WITH THIS BID.

Work must be completed and approved within 90 days of issuance of the NOTICE TO PROCEED.

I hereby certify that I am a licensed by the State of Florida, Department of Business and Professional Regulation

and that I am eligible to participate in Glades County housing Programs. I also agree that change orders above

the original contract amount shall only be paid for with housing program funds to correct documented code

violations or to meet Section 8 housing Quality Standards. Change orders must be approved by the homeowner

or his or her representative, the contractor and local government prior to any initiation of work based on that

change order.

Contractor’s Name (Print) _________________________________________________________________

Contractor’s Address _________________________________________________________________

Contractor’s phone number _________________________________________________________________

Contractor’s Insurance __________________________________________________________________

Date submitted : ___________________ Date Accepted : ____________________

Work write-up prepared by: Narrisa Pannell, SHIP Coordinator

By Signing above, the Responder certified that he or she has read and understands the provisions

contained in the RFP and agrees with all the terms, conditions, and specifications as contained and

made reference to in this proposal as well as any attachments thereto. By signing this Bid the person

signing acknowledges and affirms that they have the legal authority to do so.

Name

Company Name

Authorized Signature

Date

Homeowner signature : __________________________________________________________________________

Page 17 of 27

Revised 05/27/2025

This page summarizes the opportunity, including an overview and a preview of the attached documents.

Title	Description	Type	Submission Deadline
Request for Proposal RFP #2026 - Rehab-Eagle,D	Glades County is seeking bid proposals for the construction services under the Housing Rehabilitation Program for the property located at 300 5th Street NW, Moore Haven, Florida. Scope of Work	Sealed Bid	All responses must be sealed and received by the County at 198 6th Street SW, Moore Haven, Florida 33471, on or before 4:.30 p.m. EDT on Monday, July 6, 2026.

the construction services

Attachment Preview

Sign-up for a Free Trial, Government Bid Alerts

See Also