Purchase of Two (2) Submersible Pumps for San Marino LS09

Agency:	Mobile Water Service System(MAWSS)
State:	Alabama
Type of Government:	State & Local
NAICS Category:	423830 - Industrial Machinery and Equipment Merchant Wholesalers
Posted Date:	May 26, 2026
Due Date:	May 29, 2026
Solicitation No:	IFB 26-033
Original Source:	Please Login to View Page
Contact information:	Please Login to View Page
Bid Documents:	Please Login to View Page

Attachment Preview

Joyce Sawyer, Buyer II

(251) 694-3110 Office

jasawyer@mawss.com

INVITATION FOR BID

MAY 26, 2026

Mobile Area Water and

Sewer System

4725 Moffett Road

Mobile, AL 36618-2236

PO Box 180249

Mobile, AL 36618-0249

INVITATION FOR BID NUMBER

IFB 26-033

NAME OF BID

BIDS WILL BE RECEIVED AT

BID OPENING DATE

Purchase of Two (2) Submersible Pumps for San Marino LS096

MAWSS Purchasing Dept. Bid Box

East Visitor Entrance

4725 Moffett Road

Mobile, AL 36618

If sending bids by UPS/Fed Ex, deliver to the Warehouse:

1610 Shelton Beach Rd. Ext., Mobile, AL 36618

with IFB# marked on envelope

May 29, 2026

BID CLOSING TIME

12:00 pm Central Time

AWARD WILL BE MADE BY

MATERIAL DELIVERED TO

ADDITIONAL INFORMATION CONTACT

Total Cost & Lead Time

MAWSS – Lift Station Department

1610 Shelton Beach Road Ext.

Mobile, AL 36618

Terry Herman at (251) 378-3509 or therman@mawss.com

APPLICABLE SDP POLICY

None

Sealed bids must be in the Purchasing Department no later than the time specified in order to be considered. Submissions

received after the deadline will not be considered. Envelopes must bear the name of the supplier, company address and the

words “IFB 26-033 Submersible Pumps Purchase” or “IFB 26-033 NO QUOTE.” Facsimile or email bids will not be accepted.

All bids must be submitted on the attached forms, or your bid will be disqualified. Bidder shall furnish all the information

required by the solicitation. The bidder’s name must be typed or printed on the bid sheet and signed by the bidder or

appropriate authorized executive officer of the bidder’s company. Bidders must initial any changes or erasures. Bidders should

retain a copy of bids for their records.

Bidders shall acknowledge receipt of all addenda to this solicitation by signing and returning each addendum or by identifying

the addendum number and the date on the bid form. Failure to acknowledge receipt of any addendum by a bidder will result

in rejection of the bid if MAWSS determines that the addendum contains information that materially changes the requirements.

All bids shall be quoted FOB Destination, freight prepaid with no additional charges. Unless otherwise specified in the bid, all

prices will be on a firm-fixed price basis and are not subject to adjustments based on costs incurred. MAWSS reserves the right

to reject any or all bids submitted, to waive any informality in any bid or in the bid process, or to terminate the bid process at

any time, if deemed by MAWSS to be in MAWSS’s best interest.

A Purchase Order and this “Invitation for Bid” with “Specifications,” “Conditions,” “Bid Form,” signed by the successful bidder’s

authorized representative, and all attached drawings and other documents furnished by MAWSS to the bidders with the

Invitation for Bid in order to illustrate the contract requirements, will constitute a contract for the goods and/or services to be

purchased.

IFB 26-033 Submersible Pumps Purchase

Page 1 of 6

IFB 26-033 SUBMERSIBLE PUMPS PURCHASE

CONDITIONS

The Board of Water and Sewer Commissioners of the City of Mobile will accept bids for the Submersible Pumps Purchase in

our Purchasing Department Bid Box located at the East Visitor Entrance at 4725 Moffett Road, Mobile, AL. 36618 no later than

12:00 p.m. local time on May 29, 2026. Bids will be opened immediately after bid closing time in the Operations Center Board

room located at the East Visitor Entrance. Award will be by Total Cost & Lead Time. The bidder offers and agrees, if this bid is

accepted, to furnish the items as defined in the specifications for the unit price set opposite each item. Pricing shall be FOB

Mobile, Alabama. All items shall be delivered to our Lift Station Dept. located at 1610 Shelton Beach Rd. Ext., Mobile, AL

36618 or to the job site as needed. The bidder shall state the expected length of delivery time on the Bid Form.

Bidder understands and agrees that manufacturer and part numbers are provided for descriptive purposes only. Items of equal

or better quality will be considered but must be approved by MAWSS in writing. Upon delivery, if the quality, durability or

performance of any product represented as equal or better is determined by MAWSS to be unsatisfactory, MAWSS will require

a suitable substitute or will require that the originally specified item be delivered, at the unit price originally offered by bidder.

No substitution for items to be provided pursuant to this contract shall be permitted during the contract period without the

express written consent of MAWSS. All items provided shall be for commercial use and for the purposes reflected in the

contract documents.

No bid on closed out or discontinued item(s) will be accepted. Item(s) that have a determinable shelf life must be disclosed at

the time of bid submittal. Bidder understands that his/her bid shall be good and may not be withdrawn for a period of sixty

(60) calendar days after the scheduled closing time for receiving bids.

MAWSS reserves the right to reject any or all bids submitted, to waive any informality in any bid or in the bid process, or to

terminate the bid process at any time, if deemed by MAWSS to be in MAWSS’s best interest.

Bidder understands and agrees that quantities will be purchased by MAWSS on an “as needed” basis to replenish inventory.

MAWSS shall not be committed to the purchase of a pre-established minimum quantity for any one item.

A bidder may not modify its bid after bid opening. Errors in the extension of unit prices stated in a bid or in multiplication,

division, addition or subtraction in a bid may be corrected by the MAWSS Purchasing Buyer prior to award. In such cases, unit

prices shall not be changed.

It is the responsibility of the bidder to determine prior to the bid opening whether any amendment, additions, deletions or

changes of any type have been made to this Invitation for Bid, Conditions, Specifications, Bid Form or any other bid documents.

Bid documents and any amendments made to this bid will be posted on our website at www.mawss.com.

Invoices should be emailed to Accounts Payable at AcctsPayable@mawss.com.

END OF CONDITIONS

IFB 26-033 Submersible Pumps Purchase

Page 2 of 6

IFB 26-033 SUBMERSIBLE PUMPS PURCHASE

SPECIFICATIONS

This IFB is for the purchase of two (2) submersible 4” non-clog pumps for San Marino LS096, rated to

deliver 300 GPM @ 115’ TDH. The control and electrical cables shall be 50’feet long and all applicable

control relays shall be included in the quote. The vendor shall make their pump adapt to the existing claw

and guiderail assemble at no cost to MAWSS. The new pumps will be replacing ABS pumps. The

efficiency of the pumps and delivery times will be considered in the purchase evaluation.

Service:

Sewage

Type of Pump: End Suction Centrifugal - Submersible Pump

PART 1 GENERAL

1.01

Capability:

A. 3” minimum diameter spherical solid passage.

1.02

Materials of Construction:

A. Casing - cast iron A48 Class 35C or 40

B. All Exposed Bolts & Nuts - 316 stainless steel

C. Pump Exterior Coating - Factory applied primer and finish coat to suit pumped media.

D. Pump Interior – All internal wetted parts including volute assembly, shall receive a ceramic-

epoxy coating as per below. Unless parts are hardened material, or coating can affect the

hydraulics of the pump.

1. Belzona®1321 (Ceramic S -Metal) (Minimum 24 dry mils thickness) shall be

applied blue topcoat and gray basecoat (to ensure successful overlap) by brush,

applicator, or spray at a typical thickness of 15 mils per coat. The first coat shall not

be left more than 24 hours before overcoating with the second coat. Evidence of

basecoat shall not be identifiable upon completion.

E. Shaft & Sleeve - Stainless steel AISI 431 or 420

F. Impeller - Hard Iron (ASTM A-532 (Alloy 111A) 25% chrome cast iron. And shall have

hard iron wear ring or wear plate with equal hardness to the impeller. The impeller shall not

be a Vortex style.

G. O-Rings - Viton

H. Upper Bearing - Single row deep groove ball bearing.

I. Lower Bearing - Two row angular contact ball bearing.

J. All mating surfaces where watertight sealing is required shall be machined and fitted with

Viton rubber O-rings. Fitting shall be such that sealing is accomplished by metal-to-metal

contact between machine surfaces. This will result in controlled compression of nitrile

rubber O-ring without requirement of a specific torque limit.

IFB 26-033 Submersible Pumps Purchase

Page 3 of 6

1.03

Drive Motor:

A. 240 VAC, 60HZ 3 Phase.

B. Design – Squirrel-Cage, Induction.

C. NEMA Design – Type B

D. Windings – Copper, Class H Insulated rated for 180 degrees C

E. Service Factor – 1.15 continuous.

F. Design Temperature – 40°C ambient.

G. Non-overloading at any point on pump curve

H. Explosion Proof

I. Air filled or oil motor when required herein, pumps shall have a cooling jacket to allow

continuous operation in an unsubmerged condition. Cooling jackets may have closed

integral, liquid cooling system.

J. Motor Terminal Board

K. Stator shall be heat-shrink fitted.

L. Motor Winding Over Temperature Thermostats

M. Seal Failure Moisture Probe

N. Motor cables shall be designed for submersible duty and shall be indicated by code or legend

permanently applied to cable.

O. The control and electrical cables shall be minimum 50 feet long.

1.04

Warranty:

A. The warranty shall be 100% (parts and labor) for the first year, 50% from the beginning of

the second year to the end of the fifth year. The units shall be warranted by the manufacturer

for a five-year period. Wear items such as seals, bearings impellers, rotors and stators may

be prorated during the five-year period.

1.05

Submittals:

A. Manufacturer’s literature, specifications, and engineering data including dimensions,

material, size and weight. Performance data and curves showing pump efficiencies, flow

rate, head, brake HP, motor HP, speed, and shut-off head.

B. Operation and maintenance manuals including complete installation, operation and

maintenance data including installation and wiring diagrams.

C. A complete parts list and exploded view diagram of the pump.

IFB 26-033 Submersible Pumps Purchase

Page 4 of 6

1.06

Manufacturer(s):

A. Acceptable manufactures include:

1. Flygt

2. KSB

3. Wilo

END OF SPECIFICATIONS

IFB 26-033 Submersible Pumps Purchase

Page 5 of 6

This page summarizes the opportunity, including an overview and a preview of the attached documents.

Purchase of Two (2) Submersible Pumps for San Marino LS09

Attachment Preview

Sign-up for a Free Trial, Government Bid Alerts

See Also