MOTOR,ALTERNATING C

Active

Contract Opportunity

ITEM UNIQUE IDENTIFICATION AND VALUATION (JAN 2023)|19|.|||||||||||||||||||
HIGHER-LEVEL CONTRACT QUALITY REQUIREMENT|8|.||||||||
DESIRED AND REQUIRED TIME OF DELIVERY (JUNE 1997)|29|0001|21 Each|90|||||||||||||||||||||||||||
NAVY USE OF ABILITYONE SUPPORT CONTRACTOR - RELEASE OF OFFEROR INFORMATION (3-18))|1|.|
EQUAL OPPORTUITY FOR WORKERS WITH DISABILITIES (JUN 2020)|2|.||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM-BASIC (FEB 2024)|11|.|||||||||||
ALTERNATE A, ANNUAL REPRESENTATIONS AND CERTIFICATIONS (OCT 2024)|13|.|||||||||||||
BUY AMERICAN-FREE TRADE AGREEMENTS-BALANCE OF PAYMENTS PROGRAM CERTIFICATE-BASIC (FEB 2024))|5|.|||||
BUY AMERICAN--BALANCE OF PAYMENTS PROGRAM (FEB 2024)|1|.|
ANNUAL REPRESENTATIONS AND CERTIFICATIONS (MAR 2025)(DEVIATION 2025-O0003 AND 2025-O0004))|12|335312|1250|||||||||||
FACSIMILE PROPOSALS (OCT 1997)|1|In lieu of fax, elizabeth.chesebro@dla.mil|
NOTICE OF PRIORITY RATING FOR NATIONAL DEFENSE, EMERGENCY PREPAREDNESS, ANDENERGY PROGRAM USE (APR 2008))|2||x|
1. SCOPE
1.1 The material covered in this contract/purchase order will be used in a
crucial shipboard system enabling the launch and/or recovery of aircraft. The use of incorrect or defective material would create a high probability of failure resulting in a serious personnel injury, loss of life, loss of vital
shipboard systems or loss of aircraft. Therefore,the material has been
designated as Critical material and special control procedures are invoked
to ensure receipt of correct material.
1.2 Articles to be furnished hereunder shall be manufactured, tested and inspected in accordance with ;NAWCAD LAKEHURST; drawing number ( ;6532D009-1; ) ;36334; , Revision ;REV L; and all details and specifications referenced therein.
1.3 Unless expressly provided for elsewhere in this clause, equipment such as fixtures, jigs, dies, patterns, mylars, special tooling, test equipment, or any other manufacturing aid required for the manufacture and/or testing of the subject item(s) will not be
provided by the Government or any other source and is the sole responsibility of the contractor. The foregoing applies notwithstanding any reference to such equipment or the furnishing thereof that may be contained in any drawing or referenced specification.
1.4 If MIL-STD-454 is referenced in the drawings or in the specification, the contractor is expected to show compliance with IPC/EIAJ-STD-001C.
2. APPLICABLE DOCUMENTS - NOT APPLICABLE
3. REQUIREMENTS - NOT APPLICABLE
4. QUALITY ASSURANCE
1. For purposes of this TDR, the term NDT shall refer to the following methods: MT-Magnetic Particle Testing, PT-Penetrant Inspection, UT-Ultrasonic Testing, RT-Radiographic Testing, and VT-Visual Testing.
2. Companies performing NDT shall be NADCAP accredited, or a laboratory accredited by one of the organizations listed belowas satisfying ISO 17025 (General requirements for the competence of testing and calibration laboratories). NDT certificates shall be bear
the symbols of accreditation and the accreditation body:
a. American Association for Laboratory Accreditation (A2LA)
b. ANSI National Accreditation Board (ANAB)
c. International Accreditation Service, Inc (IAS)
d. National Voluntary Laboratory Accreditation Program (NVLAP)
e. Perry Johnson Laboratory Accreditation, Inc (PJLA)
f. Canadian Association for Laboratory Accreditation Inc. (CALA)
g. Standards Council of Canada (SCC)
5. PACKAGING- MIL-STD 2073 PACKAGING APPLIES AS FOUND ELSEWHERE IN THE SCHEDULE
6. NOTES - NOT APPLICABLE
THIS ALRE ITEM HAS BEEN IDENTIFIED AS NON-CRITICAL.
NAVSUP REFERENCE ONLY: PROCUREMENT TDR 24-10066.

Attachments/Links