Maintenance, Repair, and Preservation of TWR 7 and 8

Active

Contract Opportunity

The Regional Maintenance Center at Puget Sound Naval Shipyard and Intermediate Maintenance Facility (PSNS and IMF), Bremerton, Washington intends to award a stand-alone Firm-Fixed-Price contract to accomplish pierside modernization of two (2) Naval vessels, TWR-7 and TWR-8. Work will be accomplished at the Contractors facility.TWR-7Length: 85FTWidth: 21 FT 6 INAge: 16 YRSHull Type: Aluminum Draft: 5 FT 8 INFull Displacement: 95 Tons Light Load: 60 Tons Scope Overview: Coordinate with the Contracting Officer, via the Contracting Officers Representative (COR) to have vessel delivered to the Contractors facility. Upon docking vessel, wash, and clean vessel. Remove all fendering and sweep blast clean and replace any broken or missing studs and related hardware, as well as doubler plating. Sweep blast and touch up underwater hull. Remove and Install new FWD escape hatches and gaskets. Open, clean and inspect all tanks and voids including fuel, CHT and potable water tanks. Touch up preservation of main deck and bulwarks and pilot house. Install new multi-cable penetrations in the pilot house overhead. Accomplish overhaul of bow thruster and related testing. Overhaul hydraulic steering rams and related testing. Remove, clean and inspect shafts and reinstall with new seals and bearings and accomplish related testing. Replace legacy low pressure air compressor and related piping system. Replace HVAC system and related piping. Clean and inspect main engine heat exchangers. Overhaul and test genset alternators. Flush, clean and inspect chill water piping. Replace hull valves with new. Undock the vessel. Conduct Sea trials. Arrange and coordinate the delivery of the vessel back to the Government with the Contracting Officer via the COR.TWR-8Length: 85 FTWidth: 21 FT 6 INAge: 16 YRSHull Type: Aluminum Draft: 5 FT 8 INFull Displacement: 95 Tons Light Load: 60 Tons Scope Overview: Coordinate with the Contracting Officer, via the Contracting Officers Representative (COR) to deliver the vessel to the Contractors facility. Upon docking vessel, wash, and clean vessel. Remove all fendering and sweep blast clean and replace any broken or missing studs and related hardware, as well as doubler plating. Sweep blast and touch up underwater hull. Remove and Install new FWD escape hatches and gaskets. Open, clean and inspect all tanks and voids including fuel, CHT and potable water tanks. Touch up preservation of main deck and bulwarks and pilot house. Remove insulation and install new lagging and insulation in the pilot house overhead. Repair superstructure door and replace gasket and conduct operational test. Accomplish overhaul of bow thruster and related testing. Overhaul hydraulic steering rams and related testing. Remove, clean and inspect shafts and reinstall with new seals and bearings and accomplish related testing. Replace legacy low pressure air compressor and related piping system. Clean and inspect main engine heat exchangers. Overhaul and test genset alternators. Flush, clean and inspect chill water piping. Replace hull valves with new. Purchase and install new helm chair. Undock the vessel. Arrange and coordinate the delivery of the vessel back to the Government with the Contracting Officer via the COR. The contractors facility must possess the capability of accommodating both TWR with the dimensions as stated above. To facilitate proper government oversight, the facility shall be located in the Puget Sound, WA region. For this procurement, the Puget Sound, WA region is defined as the West Coast of the continental US, starting from Olympia, WA and extending northward to Bellingham, WA. The expected period of performance is scheduled to be 03 June 2025 to 21 November 2025.The Government is contemplating a 100% Small Business set-aside under the North American Industry Classification System (NAICS) 336611, size standard 1,300 employees. The Government intends to post a request for proposals in January/February 2025 and anticipates award of the Firm-Fixed Price, stand-alone contract in April 2025 to the responsible contractor on a lowest price, technically acceptable basis in accordance with, but not limited to, the Federal Acquisition Regulation (FAR) 15.101-2. Offerors can view and/or download the draft notional work specifications for review at https://www.sam.gov.All offerors must be registered with the System for Award Management (SAM) to receive award of Government contracts. Offerors are advised also that SAM representations and certifications can be completed electronically via the System for Award Management website at https://www.sam.gov.

Attachments/Links