Furnish & Deliver Fully Automated Nucleic Acid Extraction Workstation

Invitation to bid to furnish and deliver a Fully
Automated Nucleic Acid Extraction Workstation for the
Biology Department
State Of Louisiana
Southeastern Louisiana University
Hammond, Louisiana
Cover Page
Issuing Agency:
Southeastern Louisiana University
Purchasing Department
SLU 10800
Hammond, LA 70402-0800
Director of Purchasing: Richard Himber
Procurement Specialist: Misty Betz
Telephone: (985) 549-5414
Requisitioned By: Kyle Piller
Telephone: (985) 549-
Release Date: April 27, 2026
Deadline for Fax Inquiries: April 29, 2026
Fax To: 985-549-3810
Attn: Misty Betz
Bid Opening Date: May 14, 2026
Bid Opening Time: 4:00 p.m., Central Time
Bid Opening Location:
Southeastern Louisiana University
Purchasing Department
Property Control & Supply Building
2400 North Oak Street
Hammond, Louisiana
This ITB is available in electronic form at
https://wwwcfprd.doa.louisiana.gov/OSP/LaPAC/dspBid.cfm?search=department&term=
42 It is available in PDF format or in printed form by submitting a written request to the
Procurement Specialist listed above. It is the Bidder's responsibility to check the Office
of State Purchasing LaPAC website frequently for any possible addenda that maybe
issued. Southeastern is not responsible for a bidder's failure to download any addenda
documents required to complete an Invitation to Bid.

Page 2 of 17
State Of Louisiana
Southeastern Louisiana University
Hammond, Louisiana
The Southeastern Louisiana University (SLU) Purchasing Department will receive sealed
bids until 4:00 P.M. on the bid opening date specified in the solicitation document. No bid
responses will be considered by the SLU Purchasing Department after 4:00 P.M.
Beginning at that time, bids shall be publicly opened and read aloud to those present in the
SLU Purchasing Department.
Delivery Address:
Mailing Address: Southeastern LA University
Southeastern LA University Purchasing Department
Purchasing Department Property Control & Supply Bldg.
SLU 10800 2400 North Oak St.
Hammond, LA 70402 Hammond, LA 70402
Bids submitted are subject to LA R.S. 39:1551-1736; Purchasing Rules and Regulations;
Executive Orders; General Conditions; any Special Conditions; and Specifications listed in
the solicitation document.
The purpose of this solicitation is to set forth the requirements and specifications of
Southeastern Louisiana University. The contents of this solicitation and the Bidder/
Vendor/ Contractor's bid response shall become contractual obligations if a contract
(purchase order) ensues.
Instructions to Bidders
1) Bid Forms: Per LA R.S. 39:1556, all written bids, unless otherwise provided for,
must be submitted on, and in accordance with, forms provided, properly signed in
ink or electronic signature by an authorized representative of the bidding entity.
Bids submitted in the following manner will not be accepted: (1) Bid contains no
signature indicating intent to be bound; (2) Bid filled out in pencil; (3) Bid sent by
facsimile equipment or email. Price alterations to bid responses received before bid
opening time will be considered provided the written price alteration has been
received and timestamped before bid opening time. Any other alterations of the bid
response form or foreign conditions attached thereto may cause rejection of the bid
response without further consideration.
2) Standard of Quality: Any product or service bid shall conform to all applicable
Federal and State laws and regulations and specifications contained in the
solicitation document. Unless otherwise specified in the solicitation document, any
manufacturer's name, trade name, brand name, or catalog number used in the
specifications is for the purpose of describing the quality level and characteristic
required. Bidder should specify the brand and model number of the product

Page 3 of 17
offered in his bid. Bids not specifying brand and model number shall be
considered as offering the exact products specified in the solicitation document.
3) Descriptive Information: Bidders proposing an equivalent brand or model should
submit with the bid response information (such as illustrations, descriptive
literature, and technical data) sufficient for the University to evaluate quality,
suitability, and compliance with the specifications of the solicitation document.
Failure to submit descriptive information may cause bid to be rejected. Any
change made to a manufacturer's published specification submitted for a product
shall be verifiable by the manufacturer. If item(s) bid does not comply with
specifications (including brand and/or product number), bidder should state in what
respect the item(s) deviate. Failure to note exceptions on the response form will
not relieve the successful bidder(s) from supplying the actual products requested.
4) Bid Opening: Bidders may attend the bid opening, but no information or opinions
concerning the ultimate contract award will be given at the bid opening or during
the evaluation process. Bids may be examined 72 hours after request is made.
Information pertaining to completed files may be secured by visiting the SLU
Purchasing Department during normal working hours. Written bid tabulations will
not be furnished.
5) Louisiana Preference: Preference is hereby given to products produced,
manufactured, harvested, grown or assembled in Louisiana which are equal in
quality to products produced, manufactured, harvested, grown or assembled
outside of Louisiana. The bidder shall state his right to claim the ten percent (10%)
preference in his bid response and the bidder should state the respective Louisiana
location where each qualifying item is produced, manufactured, harvested, grown
or assembled.
6) Notice of Special Programs Available
for Small Business: https://www.opportunitylouisiana.com/small-business/special-
programs-for-small-business
7) Signature Authority: In accordance with LA Revised Statute 39:1594 (Act 121), the
person signing the bid must be: (1) A current corporate officer, partnership member
or other individual specifically authorized to submit a bid as reflected in the
appropriate records on file with the Secretary of State; or (2) An individual
authorized to bind the vendor as reflected by an accompanying or as provided
upon request a corporate resolution or affidavit. By signing the bid, the bidder
certifies compliance with the above.

Page 4 of 17
General Conditions
The SLU Purchasing Department reserves the right to award items separately, grouped or
on an all-or-none basis and to reject any or all bids and waive any informalities.
1) Prices: Unless otherwise specified in the solicitation, bid prices shall be complete,
including transportation and handling prepaid by the bidder to destination - SLU,
Hammond, LA. Bids other than FOB destination may be rejected. Bid prices
should be quoted in the unit of measure stated. Bid prices shall be firm for a
minimum of thirty (30) calendar days, unless otherwise specified by SLU in the
solicitation document.
2) Payment Terms: Cash discounts for less than 30 days may be offered, but will not
be considered in determining awards. Bids containing "payment in advance" or
"COD" requirements may be rejected. Payment is to be made within 30 days after
receipt of properly executed invoice or delivery, whichever is later.
3) Delivery: Bids may be rejected if the delivery time indicated is longer than that
specified in the solicitation document.
4) Taxes: Bidder is responsible for including all applicable taxes in the bid price. The
University is currently exempt from Louisiana State Sales and Use Taxes, and local
parish and city taxes. An exemption certificate for state sales and use tax can be
provided upon request.
5) New Products: Unless specifically called for in the solicitation document, all
products for purchase must be new, never previously used, and the current model
and/or packaging. No remanufactured, demonstrator, used or irregular product will
be considered for purchase unless otherwise specified in the solicitation document.
The manufacturer's standard warranty will apply unless otherwise stated in
solicitation.
6) Default of Contractor: Failure to deliver within the time specified in the solicitation
document will constitute a default and may cause cancellation of the contract.
Where the University has determined the contractor to be in default, the state
reserves the right to purchase any or all products or services covered by the
contract on the open market and to charge the contractor with cost in excess of the
contract price. Until such assessed charges have been paid, no subsequent bid
from the defaulting contractor will be considered.
7) Contract Cancellation: The University shall have the right to cancel any contract, in
accordance with Purchasing Rules and Regulations, for cause, including but not
limited to, the following: (1) failure of the vendor to deliver within the time specified
in the contract; (2) failure of the product or service to meet specifications, conform
to sample quality, or to be delivered in good condition; (3) misrepresentation by the
contractor; (4) fraud, collusion, conspiracy or other unlawful means of obtaining any
contract with the state; (5) conflict of contract provisions with constitutional or
statutory provisions of state or federal law; (6) any other breach of contract.

Page 5 of 17
8) Applicable Law: All contracts shall be construed in accordance with and governed
by the laws of the State of Louisiana.
9) Equal Opportunity: By submitting and signing this bid, bidder agrees that he will not
discriminate in the rendering of services to and/or employment of individuals
because of race, color, religion, sex, age, national origin, handicap, disability,
veteran status, or any other non-merit factor.
10) By submitting a response to this solicitation, the bidder or proposer certifies and
agrees that the following information is correct: In preparing its response, the bidder
or proposer has considered all proposals submitted from qualified, potential
subcontractors and suppliers, and has not, in the solicitation, selection, or
commercial treatment of any subcontractor or supplier, refused to transact or
terminated business activities, or taken other actions intended to limit commercial
relations, with a person or entity that is engaging in commercial transactions
in Israel or Israeli-controlled territories, with the specific intent to accomplish a
boycott or divestment of Israel. The bidder also has not retaliated against any
person or other entity for reporting such refusal, termination, or commercially
limiting actions. The state reserves the right to reject the response of the bidder or
proposer if this certification is subsequently determined to be false, and to terminate
any contract awarded based on such a false response.
11) Louisiana Revised Statute 39:1753.1 requirements shall apply to any equipment
component which enables any form of connectivity.
12) Piggyback: Other Louisiana Governmental Agencies may purchase at the same
terms and conditions if agreed upon by awarded vendor.
13) Prohibition of Companies That Discriminate Against Firearm and Ammunition
Industries: In accordance with La.R.S. 39:1602.2, the following applies to any
competitive sealed bids, competitive sealed proposals, or contract(s) with a value of
$100,000 or more involving a for-profit company with at least fifty full-time
employees: Unless otherwise exempted by law, by submitting a response to this
solicitation or entering into this contract, the Bidder, Proposer or Contractor certifies
the following:
a. The company does not have a practice, policy, guidance or directive that
discriminates against a firearm entity or firearm trade association based
solely on the entity's or association's status as a firearm entity or firearm
trade association;
b. The company will not discriminate against a firearm entity or firearm trade
association during the term of the contract based solely on the entity's or
association's status as a firearm entity or firearm trade association.
The State reserves the right to reject the response of the Bidder, Proposer or
Contractor if this certification is subsequently determined to be false, and to
terminate any contract awarded based on such a false response or if the
certification is no longer true.

Page 6 of 17
Bid Response Form
Bidder's Name:
Mailing Address: Telephone Number:
City, State, Zip Code: Fax Number:
Email Address:
Scope: To Furnish and Deliver Fully Automated Nucleic Acid Extraction
Workstation for the Biology Department
I/we do hereby acknowledge receipt of the following addenda (if any):
Addendum number and date:
Addendum number and date:
Other Requirements:
Bidder shall include the cost of transportation and handling in the unit price of item
offered -- F.O.B. University, Hammond, LA.
If bidding other than the specified make and model, then the bidder should attach
illustrations and descriptive literature of the item(s) offered to the bid response form
for evaluation purposes.
The attached Instructions to Bidders/General Conditions shall be a part hereof.
To the Vendor:
Whenever brand name specifications or catalogue numbers are used to describe
the standard of quality, performance and other characteristics, the use of such
specifications shall not restrict unless otherwise specified, the submission of
equivalent products.
This solicitation is a sealed bid and must be returned by mail or delivered in person.
Bid response forms cannot be faxed and any fax responses shall be rejected.
Terms: Net 30 Prox., F.O.B., Hammond, Louisiana.
Taxes: Any taxes, other than state sales and use tax, shall be included within the bidder's
unit price. The University is currently exempt from state sales and use tax.
Signature to the Bid Response Form shall be construed of acceptance of the Invitation to
Bid in its entirety.
Authorized Officer Signature:
Printed Name:
Title: Date:

Bid Response Page
Item Description Qty Price Total
No.
1. Fully Automated Nucleic Acid 1
Extraction Workstation
2. Warranty 1
3. Training 1
Total Bid Amount
Name of Company:
Date:
Bidder's Initials:
See Next Page for Specifications

Specifications
Item: Fully Automated Nucleic Acid Extraction Workstation
Item Description: A fully automated system capable of performing magnetic bead-based
DNA/RNA extraction workflows, including sample preparation, purification, and transfer.
The equipment provided must be new and delivered as a fully integrated system. The
vendor shall include all necessary components for complete functionality, including
hardware, software, and all required accessories. In addition, the vendor is responsible
for providing installation and comprehensive training for laboratory personnel. The
system must be delivered as a turnkey solution, fully operational and ready for
immediate use in a laboratory setting upon completion of installation.
Specific Features
1. Core System
1.1. The system must be an enclosed automated liquid handling workstation with a
high-density deck configuration (9 mm spacing), designed to minimize
contamination and support high-throughput nucleic acid extraction workflows.
1.2. The system must include a minimum of four (4) independent pipetting channels
with a pipetting range of 1 L to 1000 L and support dynamic positioning for
non-uniform sample processing.
2. Extraction Technology
2.1. The system must include a fully integrated magnetic bead-based extraction
module utilizing a magnetic rod-based separation mechanism capable of
automated nucleic acid purification.
2.2. The system must support:
2.2.1. DNA and RNA extraction workflows
2.2.2. High molecular weight DNA extraction
2.2.3. 96-well deep well plate processing
2.3. The system must be compatible with commercially available magnetic bead-
based extraction kits for blood and tissue samples and support standardized
extraction protocols.
3. Integrated Processing Features
3.1. The system must include:
3.1.1. Automated plate handling and transport using an integrated gripper
mechanism
3.1.2. Capability for parallel processing of multiple plates
3.1.3. A dual-position or equivalent automated processing system to allow
simultaneous preparation and extraction steps
3.1.4. Integrated workflow coordination between liquid handling and magnetic
extraction modules
4. Pipetting and Contamination Control
4.1. The system must include:
4.1.1. Air displacement pipetting technology
4.1.2. Real-time aspiration monitoring
4.1.3. Pressure-based aspiration and dispense verification

Page 9 of 17
4.1.4. Anti-droplet control technology
4.1.5. Precision tip attachment mechanism with minimal mechanical force
4.1.6. Aerosol-free tip ejection technology
4.1.7. Dual liquid level detection (capacitive and pressure-based
5. System Hardware Configuration
5.1. The system must include a modular deck configuration with:
5.1.1. Multi-position carrier bases
5.1.2. Stacked and standard carriers
5.1.3. Pedestals for:
5.1.3.1. Deep well plates
5.1.3.2. Filter tip racks
5.1.3.3. Multi-tube adapters
5.1.3.4. Reagent reservoirs (including 50 mL and 200 mL formats)
5.1.4. Reagent carrier systems with low dead volume design
5.2. The system must support flexible workflow configuration for complex extraction
protocols.
6. Workflow Capabilities
6.1. Must support:
6.1.1. Non-uniform sample layouts
6.1.2. Variable volume pipetting
6.1.3. Complex workflows (e.g., cherry picking)
6.2. Must allow fully automated walk-away operation
7. Software
7.1. The system must include an advanced integrated control software platform
capable of:
7.1.1. Workflow programming and automation
7.1.2. Real-time process monitoring
7.1.3. Error detection and recovery
7.1.4. Audit trail generation
7.2. The software must support custom protocol development and graphical workflow
design.
8. Physical Requirements
8.1. System must:
8.1.1. Fit within standard laboratory space
8.1.2. Have dimensions not exceeding:
8.1.2.1. Depth: 28 inches
8.1.2.2. Height: 36 inches
8.1.2.3. Width: 66 inches
9. System Components
9.1. The system must include:
9.1.1. Integrated system controller (computer workstation)
9.1.2. Barcode scanning capability for sample tracking

Page 10 of 17
9.1.3. Pipetting verification kit
9.1.4. Compatibility with conductive pipette tips and reagent reservoirs suitable
for automated systems
10. Performance Requirements
10.1. The system must be capable of performing high-throughput nucleic acid
extraction while maintaining consistent, high-quality results. It shall ensure high
reproducibility and yield across all runs, and must be designed to minimize the
risk of contamination throughout the extraction process.
11. Installation
11.1. Vendor must provide:
11.1.1. On-site installation
11.1.2. Installation Qualification (IQ) and Operational Qualification (OQ)
11.1.3. Pipetting verification and system validation
12. Training
12.1. Vendor must provide:
12.1.1. Operator training and method setup support
13. Warranty and Support
13.1. The system must be supported by a minimum one (1) year warranty
covering parts and labor. The vendor shall ensure ongoing availability of
technical support and service to maintain optimal system performance. In
addition, the vendor must provide reliable access to necessary consumables
and replacement parts to support continuous laboratory operations.
14. Delivery Requirements
14.1. Delivery shall be FOB Destination to Southeastern Louisiana University,
with all shipping responsibilities borne by the vendor until the equipment is
received at the designated location. Vendor must provide inside delivery (white-
glove service) including delivery to final location, unpacking, and debris removal.
15. Evaluation Criteria
15.1. Bids will be evaluated based on the degree of compliance with the stated
specifications, as well as the overall technical performance of the proposed
system. Consideration will also be given to the total cost and the vendor's
demonstrated experience, including the quality of support and service provided.
Contact Information
Dr. Kyle Piller Hammond, Louisiana
Director for Environmental Research (985) 549-2191
Department of Biological Sciences kyle.piller@selu.edu
Southeastern Louisiana University
Vendor must include all expenses (this includes shipping and discounts) in the
unit price.
See following pages for insurance requirements.