CSP 26.15 - Chiller Replacement Project Addendum No. 1 | Texas Government Bid

Agency:	Beaumont Independent School District
State:	Texas
Type of Government:	State & Local
NAICS Category:	238220 - Plumbing, Heating, and Air-Conditioning Contractors
Posted Date:	May 22, 2026
Due Date:	Jun 4, 2026
Original Source:	Please Login to View Page
Contact information:	Please Login to View Page
Bid Documents:	Please Login to View Page

Attachment Preview

May 20, 2026

ADDENDUM NO. 1

Project:

Beaumont ISD – Chiller Replacement Project (Guess E.S.)

(CSP 26.15)

Prepared by:

Salas O’Brien Engineers

10930 W. Sam Houston Parkway N., Suite 900

Houston, Texas 77064

SOBE Project No.: 2650-00566

Prepared For:

Prospective Proposers

PART A:

NOTICE TO PROPOSERS

Receipt of this Addendum shall be acknowledged on the Proposal Form. Failure

to do so may subject Proposers to disqualification. Each Proposer shall make

necessary adjustments and submit his proposal with full knowledge of all

modifications, clarifications, and supplemental data included therein.

This Addendum forms part of the Contract Documents and shall be incorporated

integrally therewith. Where provisions of the following supplemental data differ

from those of previously issued documents, this Addendum shall govern.

The following Contract Documents have been issued to date delineating the

Work (Project). Contract Documents dated: April 17, 2026

This Addendum consists of 2 typewritten pages and 1 page of attachments for a

total of 3 pages.

PART B:

PART C:

CHANGES TO PRIOR ADDENDUM

“Any changes to prior issued addendum materials are listed here.”

None

CHANGES TO THE PROJECT MANUAL

“Any changes to specifications are listed here.”

Section 23 07 19 HVAC PIPING INSULATION

a. Part 3 Execution, Article 3.6 Miscellaneous, Revise Item A to read “New base

mounted pump shall NOT be insulated. Piping insulation and vapor barrier

shall stop at flange to new pump.”

PART D:

CHANGES TO THE DRAWINGS

Sheet M1.1 - MECHANICAL DEMOLITION FLOOR PLAN – MECHANICAL

YARD

a. Replace keyed #7 in its entirety with the following: “7. EXISTING CHILLED

WATER PUMP SERVING “A&B”, ASSOCATED ISOLATION VALVES AND

APPARTATUSES SHALL BE REMOVED. EXISTING CONCRETE PAD

SHALL REMAIN AND BE REUSED.”

Sheet M2.1 – MECHANICAL FLOOR PLAN – MECHANICAL YARD

a. Replace keyed #7 in its entirety with the following: “7. EXISTING 6”

CONCRETE PAD SHALL REMAIN AND BE REUSED. EXTEND EXISTING

COPNCRETE PAD FOR NEW PUMP.”

10930 W. Sam Houston Pkwy N, Suite 900

Houston, Texas 77064

281.664.1900

salasobrien.com

Beaumont ISD – Chiller Replacement Project (Guess E.S.)

Addendum 1

PART E:

PART F:

PART G:

PART H:

Sheet M3.1 – MECHANICAL PIPING DIAGRAMS

a. Detail #1 Demolition Chilled Water Piping Diagram, Demolition Keyed Notes,

Replace keyed #6 in its entirety with the following: “6. EXISTING CHILLED

WATER PUMP SERVING “A&B”, ASSOCATED ISOLATION VALVES AND

APPARTATUSES SHALL BE REMOVED. EXISTING CONCRETE PAD

SHALL REMAIN AND BE REUSED.”

b. Detail #2 Chilled Water Piping Diagram, Keyed Notes, Replace keyed #9 in its

entirety with the following: “9. EXISTING 6” CONCRETE PAD SHALL

REMAIN AND BE REUSED. EXTEND EXISTING CONCRETE PAD FOR

NEW PUMP.”

Sheet M4.1 – MECHANICAL SCHEDULES AND DETAILS

a. Delete detail #2 in its entirety.

RE-ISSUED DRAWING SHEET (30” x 42”)

“Insert the following sheets and omit the previously issued sheets of the same number.”

None

NEW DRAWINGS SHEETS (30” x 42”)

None

QUESTIONS/CLARIFICATIONS

Question: If I need an additional site visit is it possible to make that happen?

Answer: The district has agreed to provide an additional site visit on 5/27 @

10AM.

Question: Is the district okay with moving the pump over a few feet to help with

getting the new chiller installed sooner or would the district like the new pad in

the same existing location?

Answer: The district requests the new pump to be installed in the same location

as the existing pump. The existing concrete pad will be reused and extended as

described in the addendum items above.

Question: Can we get an explanation on why the single point rather than dual

point? If the manufacturer cannot accommodate a single point connection is it an

acceptable modification to return to dual point connection?

Answer: The approved manufacturers listed in the specification each require

only a single-point electrical connection. Additionally, selecting an air-cooled

chiller with a single-point connection allows reuse of the existing overcurrent

protection with minimal disruption to the current installation. By contrast, a dual-

point connection air-cooled chiller would require a second overcurrent protective

device in the MCC or at the branch-circuit tap.

ATTACHMENTS

Pre-Proposal Sign in Sheet

END OF ADDENDUM 1

10930 W. Sam Houston Pkwy N, Suite 900

Houston, Texas 77064

281.664.1900

This page summarizes the opportunity, including an overview and a preview of the attached documents.

CSP 26.15 - Chiller Replacement Project Addendum No. 1

Attachment Preview

Sign-up for a Free Trial, Government Bid Alerts

See Also