Added: Sep 18, 2017 9:28 am
Modified: Sep 19, 2017 3:11 pm
SOURCES SOUGHT NOTICE: DOCKSIDE REPAIRS USCGC WILLIAM TRUMP
This is a SOURCES SOUGHT NOTICE / REQUEST FOR INFORMATION; not a pre-solicitation notice or solicitation for proposals/quotations. Pursuant to FAR Part 10 (Market Research), the purpose of this notice is to: (1) determine if sources capable of satisfying the agency's requirements exists, (2) determine if commercial items suitable to meet the agency's needs are available or could be modified to meet the agency's requirements, and (3) determine the commercial practices of company's engaged in providing the needed service or supply. Pursuant to FAR Part 6 and FAR Part 19, competition and set-aside decisions may be based on the results of this market research. This notice in no way obligates the Government to any further action.
REQUIREMENT: This notice is issued by the U.S. Coast Guard, Surface Force Logistics Center, Norfolk, VA to identify sources capable of providing the following:
DRYDOCK Repairs Specification: (Subject to change at the discretion of the Government)
Contractor shall provide all necessary facilities, materials, equipment, and personnel to DOCKSIDE repairs to the U.S. Coast Guard Cutter (USCGC) WILLIAM TRUMP (WPB-1111), a 154 Foot "Sentinel Class" Patrol Boat. The vessel is home ported in key West, FL. All work will be performed at the vessel's pier.
GEOGRAPHICAL RESTRICTION: None
Scope of Work: The scope of the acquisition is for the DRYDOCK repairs of the USCGC WILLIAM TRUMP (WPB-1307). This work may include, but is not limited to the following ITEMS:
Hull Plating (Side Scan), Ultrasonic Testing
Structural Analysis, 3D Laser Scan, Perform
Aluminum Hull and Structural Repairs - 1/4" Plate
Aluminum Hull and Structural Repairs - 3/16" Plate (O)
Aluminum Hull and Structural Repairs - 5/16" Plate (O)
Hull and Structural Plating Repairs -Crack (Aluminum) (O)
Hull and Structural Plating Repairs - Crack (Steel) (O)
Hull and Structural Plating Repairs - Eroded Weld (Aluminum) (O)
Steel Hull and Structural Plating Repairs (5-Pound) (O)
Steel Hull and Structural Plating Repairs (7.0 Pound, 7.5-Pound or 7.65-Pound) (O)
Steel Hull and Structural Plating Repairs, Corrugated Plate (4.0-Pound) (O)
Hull and Structural Plating Repairs (6.0-Pound or 5.63-Pound) (O)
Hull and Structural Plating -10.0-Pound Steel, Repair (O)
Appendages (U/W), Leak Test (O)
Appendages (U/W) - Internal, Preserve (O)
Voids (Non-Accessible), Leak Test (O)
Tanks (MP Fuel Stowage and Overflow), Clean and Inspect
Voids (Non-Accessible), Preserve Internal Surfaces (O)
Tanks (MP Fuel Service), Clean and Inspect
Tanks (Potable Water), Clean and Inspect
Voids (Accessible), Clean and Inspect
Tanks (Dirty Oil and Waste), Clean and Inspect
Main Diesel Engine, Renew
Propulsion Shafting, Remove, Inspect, and Reinstall
Mechanical Shaft Seal Assemblies, Overhaul
Propulsion Shaft Bearings (External), Renew (O)
Propulsion Shaft, Stern Tube Forward Bearing, Renew (O)
Propulsion Shaft, Forward Bearing Housing, Renew (O)
Propellers; Remove, Inspect, and Reinstall
Temporary Services, Provide- Cutter
Speed Doppler, Remove, Inspect, and Reinstall,- Doppler Valve, Overhaul
Sea Valves and Waster Pieces, Overhaul or Renew
Sea Strainers - Duplex (All Sizes), Overhaul
Fuel System Valves, Renew and Overhaul
Steering Gear (General), Overhaul
Rudder Assembly, Remove, Inspect and Reinstall
Fin Stabilizers (General), Overhaul
Grey Water Holding Tank(s), Clean and Inspect
Sewage Holding Tank, Clean and Inspect
Grey Water Piping, Clean and Flush
Sewage Piping, Clean and Flush
Forward Peak Compartment, Preserve
Forward Void, Preserve
Tanks (Dirty Oil), Preserve "100%" (O)
Tank (Oily Water), Preserve "100%" (O)
Tanks (Potable Water), Preserve "100%"
Bilge Surfaces, Preserve
U/W Body, Preserve (100%) Used with Side Scan)
Stern Tube Interior Surfaces, Preserve 100%(O)
Impressed Current Cathodic Protection System, Inspect and Maintain
Impressed Current Cathodic Protection System Anodes, renew (O)
Impressed Current Cathodic Pretection System Reference Cells, Renew (O)
CAPAC Anode Assembly Renew (O)
Sea Trial Performance, Support, Provide
Firemain Valves, Renew
Auxiliary Sea Water System Valves, Overhaul or Renew
Shaft Alignment Check (O)
Exhaust Piping System, Inspect
SW Heat Exchangers, Clean, Inspect and Hydro
Ship Service Diesel Generators (CAT), Renew, Both
Tank (Aft Grey Water), Preserve "100%" (O)
Tank (Sewage Vacuum Colection), Preserve "100%"
Hull Plating Freeboard, Preserve "100%"
Cathodic Protection System (Bilge and Sea Chest), Renew
Impress Current Cathodic Protection System Dielectric Shield (Capastic Fairing), Renew
Ventilation System(s), Insulation, Renew (CSMP 2015007)
Deck covering System in Galley and Mess Deck, Renew
Deck Covering, (Interior Wet/Dry), Renew (CSMP 2015-02,03,03,11
Forward Auxiliary Bilge, Preserve 100% (CSMP 2015
Sewage System, structural
Structural Analysis, 3D Laser Scan, Perform
Cradle Assemble, Disassemble and Transport
All welding and brazing shall be accomplished by trained welders who have been certified by the applicable regulatory code performance qualification procedures.
Anticipated Period of Performance: The period of performance is anticipated to be for FORTY-FIVE(45) calendar days with a start date of 17 JANUARY 2018 and end date of 02 MAR 2018. (Subject to change at the discretion of the Government)
Anticipated NAICS Code/Size Standard: The applicable NAICS Code is 336611, Ship Building and Repairing and the size standard is 1,250 employees.
Submission of Information: Companies having capabilities necessary to meet or exceed the stated requirements are invited to provide information to contribute to this market survey/sources sought notice including commercial market information and company information.
Companies may respond to this Sources Sought Notice via e-mail to Shean.E.Mohammed @uscg.mil or via fax to (757) 628-4676 (Attn: Shean Mohammed/C&P1-PBPL) no later than October 10th at 5:00PM, Eastern Time with the following information/documentation:
1. Name of Company, Address and DUNS Number.
2. Point of Contact and Phone Number.
3. Business Size applicable to the NAICS Code:
Please state which of the following apply to your company:
a. 8(a) Small Business Concern;
b. HubZone Small Business Concern;
c. Service-Disabled Veteran Owned Small Business Concern (SDVOSBC);
d. Veteran Owned Small Business Concern (VOSBC);
e. ED Woman Owned Small Business Concern (EDWOSB);
f. Woman Owned Small Business Concern (WOSBC);
g. Small Business Concern;
h. Large Business Concern
4. Documentation Verifying Small Business Certification:
Please provide the following documentation as it applies to your company:
a. If claiming 8(a) status, provide a copy of your 8(a) Certificate from SBA.
b. If claiming HuBZone status, provide a copy of your HuBZone Certificate from SBA.
c. If claiming SDVOSBC status, provide documentation that shows the Service Disable Veteran (SDV) unconditionally owns 51 % of the business, controls the management and daily operations, and holds the highest officer position in the company. Documentation should also be provided to show that the SDV has a service-connected disability that has been determined by the Department of Defense or Department of Veteran Affairs. Finally, provide documentation that shows the business is small under the NAICS code 336611.
d. If claiming VOSBC status, provide documentation that shows the Veteran unconditionally owns 51% of the business, controls the management and daily operation, make long-term decisions for the business, and holds the highest officer position in the company that works at the business fulltime during normal working hours. The documentation should also show the business is small under the NAICS code 336611.
e. If claiming EDWOSB status, provide documentation that shows the company is
at least 51% owned by one or more women who are "economically disadvantaged", and primarily managed by an economically disadvantaged woman that make long-term decisions for the business, hold the highest officer position in the business and work at the business full-time during normal working hours. The documentation should also show the business is small under the NAICS code 336611. A woman is presumed economically disadvantaged if she has a personal net worth of less than $750,000 (with some exclusions), her adjusted gross yearly income averaged over the three years preceding the certification less than $350,000, and the fair market value of all her assets is less than $6 million.
f. If claiming Woman Owned Small Business status, provide documentation that shows the company is at least 51% owned and controlled by one or more women, and primarily managed by one or more women that make long-term decisions for the business and hold the highest officer position in the business and work at the business full time during normal working hours. The women must be U.S. citizens. The documentation should also show the business is small under the NAICS code 336611.
g. If claiming Small Business status, provide documentation to show the business is small under NAICS code 336611.
5. Statement of Proposal Submission: Statement on how your company will do the work and that your company WILL submit a proposal as a prime contractor if a solicitation is issued as a result of this Sources Sought Notice.
6. Past Performance Information: Evidence of experience in work similar in type and scope to include contract numbers, project titles, and dollar amounts, points of contact and telephone numbers. If two companies are planning to conduct business and submit an offer as a Joint Venture or similar type of teaming agreement, they are requested to provide past performance information on projects of similar scope that they have performed together as a Joint Venture, if available. Providing individual past performance documentation from each company on separate projects where the two did not work together may be considered less relevant.
SAM (CCR): Interested parties should register in the System for Award Management (SAM) formely known as Central Contractor Registration (CCR) as prescribed in FAR Clause 52.232-33. The CCR can be obtained by accessing the internet at www.sam.gov or by calling 1-866-606-8220.
Disclaimer and Important Notes: This Sources Sought Notice is for market research purposes only and does not constitute a Request for Proposal/Quotation; and, it is not considered to be a commitment by the Government to award a contract nor will the Government pay for any information provided; no basis for claim against the Government shall arise as a result from a response to this Sources Sought Notice or Government use of any information provided. Failure to respond or submit information in sufficient detail may result in a company not being considered a likely offeror when making a decision on whether or how to set aside a solicitation for restricted competition. Regardless of the information obtained from this Sources Sought Notice, the Government reserves the right to consider any arrangement as deemed appropriated for this requirement. Respondents are advised that the Government is under no obligation to acknowledge receipt of the information received or provide feedback to respondents with respect to any information submitted. No proprietary, classified, confidential, or sensitive information should be included in your response to this Sources Sought Notice. The Government reserves the right to use any information provided by respondents for any purpose deemed necessary and legally appropriate, including using technical information provided by respondents in any resultant solicitation. At this time no solicitation exists; therefore, Do Not Request a Copy of the Solicitation. After a review of the responses received, a pre-solicitation notice and solicitation may be published on Federal Business Opportunities (FedBizOpps) website. It is the potential offeror's responsibility to monitor FedBizOpps for release of any future solicitation that may result from this Sources Sought Notice. However, responses to this Sources Sought Notice will not be considered adequate responses to any resultant solicitation.
SOURCES SOUGHT ONLY