Added: May 07, 2008 9:51 am
THIS IS A COMBINED SYNOPSIS/SOLICITATION for Commercial Items prepared in accordance with the format in Subpart 12.6, as supplemented with additional information included in this notice. This announcement constitutes the only solicitation; quotes are being requested and a written solicitation will not be issued.
(ii) This solicitation number N68335-08-T-0064 is issued as a competitive request for Quotation (RFQ).
(iii) This solicitation will be 100% small business set aside in accordance with FAR 52.219-6. The NAICS is 337214.
(iv) Contract Line Item Numbers (CLINS) are for the following listed items:
Overall Requirements:
-All products provided to meet the listed requirements must also be fully assembled and/or installed by the vendor.
-Installation must be coordinated with NAVAIR public works department, and therefore may require the incremental delivery of certain parts.
-Installation will be on top of a 4 raised computer access flooring
-Unless otherwise stated, all worksurfaces provided must ESD protective. Electronic components will be openly handled, and static must be dissipated and neutralized for their protection.
Workstations:
-U-Shaped Work Area
-Laboratory-grade cabinetry and casework
-Epoxy-Resin work surface
-30 deep workstations
-U-shape dimensions: 240 back with two 151 sides.
-104 of each side shall be 36 high worksurfaces. All other areas will be sitting height, 30 high surface, including corner units.
-Overhead wall-mounted 36 high cabinets, 18 above all worksurfaces.
-Worksurfaces to have a rounded bullnose front.
-120V Xenon lights mounted under all cabinet units
-Backsplashes and 125V power strips along all worksurfaces
-Two sound dampening floor cabinets with dental-grade quiet air compressor installed. Compressor systems must include quick-disconnect tubing with attachments for both a compressed air nozzle and a compressor-powered bag vacuum system.
-A 24 wardrobe unit must accompany one leg of the U-shape.
-Sink Area
-102 long, 36 high, 30 deep worksurface
-24 of floor cabinet must be sound dampening to house pumps for a circuit card fabrication system. There will be no overhead wall-mounted cabinetry above this unit.
-78 of wall-mounted cabinetry above worksurface
-120V Xenon lights mounted under all cabinet units
-Chemical resistant resin surface
-Worksurfaces to have a rounded bullnose front.
-19 x25 x12 stainless steel drop-in sink with rotating gooseneck faucet and laboratory hookup spout
-Plumbing of sink and faucet to existing hot, cold, and drain lines.
-Refrigerator/Freezer combo installed in a 24 wide open space under the 36 high worksurfaces. Must be appropriate for storage of chemicals.
-All floor cabinets must be 22 deep, with 13 of pipe space left between the rear of the cabinet, and the adjacent wall.
Mobile Workstations:
-All workstations must include custom 1-3/4 thick maple wood tops
-Metal base capable of holding a 1200 pound load.
-Items #1&2;
-Two 31 x76 mobile worksurfaces.
-36 standard height, with options for height adjustment.
-Dogbone-style latching feature to perform a flush and level joining of both worksurfaces along the 76 edge
-Carrymaster AC-600 leveling castor shall be installed on all four legs of each workstation.
-One under-surface drawer, 4 high and 21 long, on each workstation
-Item #3
-31 x76 mobile worksurface.
-36 standard height, with options for height adjustment.
-Carrymaster AC-600 leveling castor shall be installed on all four legs of workstation.
-Three under-surface drawers, 4 high and 21 long
-Radiused corners on maple top
-Item #4
-31 x76 mobile worksurface.
-36 standard height, with options for height adjustment.
-Carrymaster AC-600 leveling castor shall be installed on all four legs of workstation.
-Three under-surface drawers, 4 high and 21 long
-Square corners on maple top
-Item #5
-47 wide by 29 deep stainless steel cart. 36 height.
-1 maple wood top
- steel lip above maple top along edges
-Must have locking castors
Wall-hung Countertop:
-98 wide by 36 deep corian countertop
-Mounted on wall at 30 height.
-Must coordinate with NAVAIR Public Works dept. to install on custom brackets to enable a 600 pound load along the outer edge of said countertop. Brackets will be provided by NAVAIR.
-Does not require an ESD surface
-Must have cutouts for cable pass-through along rear of countertop.
Shelving:
-Three sets of wall-mounted 1 maple wood shelving
-Maple wood shall be provided in 48 wide by 24 deep sections
-Each section to sustain a 600 pound weight
-Must have cutouts for cable pass-through along rear shelf.
-Each row of shelving to have a metal endcap
-Shelved must be mounted with an under-shelf bracket. All installation performed by the vendor. NAVAIR public works is available to add additional studs to wall upon request.
-Item #1
-Three rows, each separated vertically by 36 of open space
-Each row to consist of 3 sections of 48 wide maple, side-by-side
-First row to begin 12 vertically from surface of floor
-Items #2 (identical to previous item)
-Three rows, each separated vertically by 36 of open space
-Each row to consist of 3 sections of 48 wide maple, side-by-side
-First row to begin 12 vertically from surface of floor
-Item #3
-Three rows, each separated vertically by 36 of open space
-Each row to consist of 2 sections of 48 wide maple, side-by-side
-First row to begin 12 vertically from surface of floor
Chairs:
-Four fabric chairs with foot ring, casters, backrest & lumbar support. 23 -28 adjusting height. Two chairs must have push-down locking castors that will prevent rolling whenever an individual is seated. The remaining two chairs do not require a locking castor.
-Three fabric chairs with foot ring, casters, backrest & lumbar support. 17 -22 adjusting height
-6 fixed height (30 ) four-legged stools with round 13 diameter maple seat
(v) Contract Terms and Conditions:
Inspection and Acceptance Section E:
DD 250. FOB Destination
Deliveries or Performance Section F:
All items shall be preserved, packaged, packed, and marked in accordance with best commercial practices. All items shall be shipped to: Lakehurst Naval Air Warfare Center, Attn: Matt Morgan,
Highway 547, Bldg. 678, Lakehurst, NJ 08733.
Contract Clauses Section I
FAR 52.212-1 Instructions to Offerors-Commercial Items, is incorporated by reference
52.212-2, Evaluation-Commercial Items is incorporated by reference. Addendum Para (a): Award will be made to lowest price offeror. Offerors shall include a completed copy of the provision at FAR 52.212-3, Offeror Representations and Certifications- Commercial Items and DFARS 252.212.7000- Offeror Representations and Certifications- Commercial Items (SEP 1995) with its offer. 52.212-4 Contract Terms and Conditions - Commercial Items. The resulting contract will be firm fixed price (FFP) 52.212-5 Contract Terms and Conditions Required to Implement Statutes or Executive Orders Commercial Items is incorporated in this contract by reference; the following provisions apply: 52.203-6, Restrictions on Subcontractor Sales to the Government with Alternate I; 52.219-14, Limitation on Subcontracting; 52.222-21, Prohibition of Segregated Facilities; 52.222-26, Equal Opportunity; 52.222-35, Affirmative Action for Disabled Veterans and Veterans of the Vietnam Era; 52.222-36, Affirmative Action for Handicapped Workers; 52.222-37, Employment Reports on Disabled Veterans and Veterans of the Vietnam Era; 52.222-19, Child Labor-Cooperation with Authorities and Remedies; 52.225-13, Restriction on Certain Foreign Purchases; 52.225-15, Sanctioned European Union Country End Products; 52.247-64 Preference for Privately Owned U.S.-Flag Commercial Vessels; 52.232-33 Payments by Electronic Funds Transfer Central Contractor registration; 252.212-7001, Contract Terms and Conditions Required to Implement Statutes or Executive Orders Applicable to the Defense Acquisitions of Commercial Items; 252.225-7001, Buy American Act and Balance of Payments Program; 252.204-7004 Alt A Central Contractor Registration Alt A; 252.232-7003 Electronic Submission of Payment Request
(vii)Quotes are due by 12:00pm EST, 23 May 2008 at the Naval Air Warfare Center Aircraft Division Lakehurst, Attn: Code 25232 Jillian Kohler, Hwy 547, Bldg. 562, Lakehurst, NJ 08733-5082. The Government will not accept faxed quotes. You may e-mail your quote to jillian.kohler@navy.mil or mail it to her at the following address: Naval Air Warfare Center Aircraft Division, Contracts Dept. Bldg 562 Attn: Jillian Kohler, Highway 547, Lakehurst NJ 08733.
(vii) Name and telephone number of individual to contact for information regarding the solicitation: Jillian Kohler, (732) 323-4586, e-mail: jillian.kohler@navy.mil. This Combined Synopsis/Solicitation will be posted on the NAVAIR homepage located at http://www.navair.navy.mil/doing_business/open_solicitation/. Hard copies of this Combined Synopsis/Solicitation and Amendments will NOT be mailed to contractors.
