To respond to this bid electronically, you must be logged in with a Premium Registration.

Bid Number:	B1E09127	Status:	Open
Agency:	OFFICE ADMINISTRATION-OPER	Total Bid Lines:	5
Description:	DRILL RIG AND TRUCK NATURAL RESOURCES DIV OF GEOLOGY AND LAND SURVEY	Closing Date: Closing Time:	11/19/2008 2:00pm CENTRAL

The information on this page provides a summary of the requirements for this bid. The official bid document includes the applicable requirements, detailed specifications, and Terms and Conditions.   In the event of any discrepancy, the official bid document will govern. To access the official bid document, click on this link:B1E09127 . A page will open with links to download the official bid document in Microsoft Word or PDF format.

IF RESPONDING ELECTRONICALLY THROUGH THE ON-LINE BIDDING/VENDOR REGISTRATION SYSTEM WEBSITE, IN ADDITION TO COMPLETING THE ON-LINE PRICING, THE PREMIUM REGISTERED BIDDER SHOULD COMPLETE AND SEND EACH EXHIBIT, AND ANY OTHER INFORMATION CONCERNING THE BID AS AN ATTACHMENT TO THE ELECTRONIC RESPONSE.

Line	Commodity
001	57800 - MISCELLANEOUS PRODUCTS--NOTEPAD TEXT ATTACHED
THE BIDDER SHALL CONFORM TO THE SPECIFICATIONS CONTAINED HEREIN. THE BIDDER SHALL SUBMIT FIRM FIXED PRICES FOR EACH ITEM THE BIDDER CHOOSES TO BID HEREIN. HOWEVER, IF THE BIDDER BIDS LINE ITEM 001, THE BIDDER MUST BID LINE ITEM 002 AND IF THE BIDDER BIDS LINE ITEM 003, THE BIDDER MUST BID LINE ITEM 004. LINE ITEM 005 IS A STAND ALONE LINE ITEM THAT INCLUDES BOTH THE DRILL RIG AND THE TRUCK. ALL PRICES QUOTED SHALL BE CONSIDERED FIRM AND FIXED. DRILL RIG WITH ONBOARD POWER UNIT FIRM, FIXED PRICE FOR DRILL RIG: SHALL INCLUDE ALL COMPONENTS AND MATERIALS WHICH ARE NECESSARY FOR THE DRILL RIG TO BE FULLY OPERATIONAL IN ACCORDANCE WITH THE SPECIFICATIONS STATED HEREIN, SHALL INCLUDE INSTALLATION AND MOUNTING OF DRILL RIG TO THE TRUCK. THE BIDDER SHALL BID LINE ITEM 002 IF BIDDING LINE ITEM 001. BIDDER SHOULD COMPLETE EXHIBIT A DETAILING THE DRILL RIG BID FOR LINE ITEM 001. DRILL RIG: SHALL BE CAPABLE OF PERFORMING AUGER BORING IN UNCONSOLIDATED FORMATIONS UTILIZING VARIOUS INDUSTRY STANDARD SIZE HOLLOW-STEM AUGERS (HSA) AND CAPABLE OF DRILLING TO AT LEAST SEVENTY (70) FEET IN DEPTH WITH INDUSTRY STANDARD FOUR AND ONE QUARTER (4.25) INCH INSIDE DIAMETER (ID) HSA; SHALL BE CAPABLE OF UTILIZING DOWN-THE-HOLE AIR HAMMER TECHNOLOGY WITH THE USE OF UP TO A MINIMUM FOUR-AND-ONE-HALF (4 1/2) INCH OUTSIDE DIAMETER (OD) DRILL ROD WITH UP TO MINIMUM LENGTH OF TEN (10) FEET AND AN AUXILIARY AIR COMPRESSOR; SHALL BE CAPABLE OF CORING APPLICATIONS TO A MINIMUM DEPTH OF ONE THOUSAND SIX HUNDRED (1,600) FEET AND SHALL HAVE THE ROTATIONAL SPEED TO PRODUCTIVELY UTILIZE NQ CORE TOOLING AS SPECIFIED IN THE SECTION FOR THE ROTARY DRIVE; COMPONENT PARTS OF THE DRILL RIG SHALL BE OF PROPER SIZE AND DESIGN TO SAFELY WITHSTAND MAXIMUM STRESSES IMPOSED BY A CAPACITY LOAD; SHALL HAVE ALL MANUFACTURERS' RECOMMENDED LUBRICATION FITTINGS; SHALL UTILIZE PARTS AND COMPONENTS SUCH AS CHAINS, BEARINGS AND UNIVERSAL JOINTS WITH MANUFACTURER'S RATINGS EXCEEDING THE LOADS AND STRESS PLACED ON THEM WHILE UNDER USE AT CAPACITY LOADS AS SPECIFIED HEREIN; SHALL HAVE A PRIMER UNDER COAT TO RETARD THE CORROSION AND PROTECT THE METAL AND A TOP COAT OF PAINT IN COLORS SPECIFIED BY THE STATE AGENCY. DRILL PLATFORM: THE DRILL PLATFORM SHALL BE CONSTRUCTED FROM A STEEL SLIP RESISTANT DECK PLATE OF SUFFICIENT STRENGTH AND THICKNESS TO WITHSTAND NORMAL WEAR AND LOADING; A WATERTIGHT TOOL BOX SHALL BE PROVIDED ON OPPOSING SIDES OF THE PLATFORM DECK; DRILL ROD AND AUGER RACKS SHALL BE FURNISHED; CLEARANCE LIGHTS SHALL BE INCLUDED; THE PLATFORM WIDTH SHALL NOT EXCEED A MAXIMUM OF NINETY-SIX (96) INCHES; A DRILLER'S STEP/STAND SHALL BE PROVIDED AND STORED AT A CONVENIENT POSITION BELOW THE DRILLER'S CONTROL PANEL; THE DRILL PLATFORM SHALL BE UNDERCOATED FOR PROTECTION AGAINST CORROSION UPRIGHT DRILL FRAME: THE UPRIGHT DRILL FRAME SHALL BE HYDRAULICALLY ACTUATED ALLOWING A NOMINAL 90 DEGREE FOLD OVER FOR TRANSPORT; DRILL FRAME SHALL BE CONTROLLED BY DOUBLE-ACTING HYDRAULIC CYLINDERS; A RESTRICTION SHALL BE PROVIDED IN THE HYDRAULIC ROUTING SYSTEM TO PREVENT THE DRILL FRAME FROM FOLDING IN AN UNSAFE MANNER DUE TO AN UNEXPECTED EMERGENCY FAILURE SITUATION DRILL POWER UNIT: SHALL BE AN ELECTRIC START, LIQUID COOLED, HEAVY DUTY INDUSTRIAL TYPE, TURBOCHARGED DIESEL ENGINE; SHALL BE EQUIPPED WITH A HEAVY-DUTY DRY TYPE REPLACEABLE ELEMENT AIR CLEANER WITH PRE-CLEANER; SHALL HAVE A FULL FLOW OIL FILTER; SHALL HAVE A MINIMUM TWELVE (12) VOLT ELECTRIC STARTING SYSTEM CONSISTING OF A STARTER, ALTERNATOR, BATTERY, REGULATOR; SHALL HAVE A METHOD OF STARTING THE POWER SOURCE AND AN ELECTRICALLY CONTROLLED ENGINE THROTTLE ON THE DRILL CONTROL PANEL; SHALL HAVE SUFFICIENT POWER TO MEET ALL REQUIREMENTS LISTED ELSEWHERE IN THIS SPECIFICATION; FUEL FOR THE POWER UNIT SHALL COME FROM THE TRUCK CARRIER FUEL TANKS HYDRAULIC SYSTEM: SHALL HAVE A HEAVY-DUTY, ENGINE DRIVEN HYDRAULIC PUMP WITH A MAXIMUM CAPACITY FOR NOT LESS THAN TWENTY-ONE (21) GALLONS PER MINUTE AT A MAXIMUM PRESSURE OF NOT LESS THAN TWO THOUSAND (2,000) PSI; SHALL BE EQUIPPED WITH A REPLACEABLE FULL FLOW ELEMENT HYDRAULIC OIL FILTER; A HYDRAULIC OIL COOLER SHALL BE FURNISHED AND THE HYDRAULIC OIL RESERVOIR SHALL HAVE ADEQUATE CAPACITY AND SHALL BE EQUIPPED WITH A VENTED FILLER CAP HYDRAULIC LEVELING JACKS: SHALL BE FURNISHED AND SHALL BE INDIVIDUALLY OPERATED FROM THE CONTROL PANEL AT THE REAR OF THE DRILL; SHALL PROVIDE ADEQUATE LEVELING CAPABILITY; SHALL BE STRONG AND RIGID ENOUGH AND SHALL EASILY SUPPORT THE TOTAL WEIGHT OF THE MACHINE PLUS THE LOAD GENERATED WHEN RETRACTING DRILLING TOOLS; CHECK VALVES SHALL BE FURNISHED IN THE HYDRAULIC LINES AND SHALL PREVENT LEAKAGE OR SLIPPAGE OF THE JACKS WHILE THE DRILL IS SET UP ON SITE; CHROME-PLATED JACK PISTON RODS SHALL BE COMPLETELY ENCLOSED TO SAFEGUARD THEM FROM DAMAGE AND FOOT PADS SHALL BE A MINIMUM OF FOURTEEN (14) INCHES DIAMETER; TWO (2) JACKS SHALL BE MOUNTED AT THE REAR OF THE PLATFORM, ONE (1) ON EACH CORNER; MAXIMUM CYLINDER TRAVEL SHALL NOT BE LESS THAN THIRTY-SIX (36) INCHES; MINIMUM OUTSIDE DIAMETER OF THE JACK CYLINDERS SHALL BE FOUR AND ONE HALF (4+) INCHES WITH A MINIMUM FOUR (4) INCH BORE AND A MINIMUM TWO-AND-ONE-HALF (2+) INCH DIAMETER PISTON ROD; MINIMUM OF ONE (1) JACK SHALL BE MOUNTED AT THE FRONT OF THE MACHINE IN A POSITION APPROPRIATE AND SHALL ALLOW FOR LEVELING THE DRILL LONGITUDINALLY WHILE IN OPERATION; MAXIMUM CYLINDER TRAVEL SHALL BE NOT LESS THAN THIRTY-SIX (36) INCHES; MINIMUM OUTSIDE DIAMETER OF THE JACK CYLINDERS SHALL NOT BE LESS THAN FOUR-AND-ONE-HALF (4+) INCHES WITH A FOUR (4) INCH BORE AND A TWO-AND-ONE-HALF (2+) INCH DIAMETER PISTON ROD; IF ONLY ONE FRONT LEVELING JACK IS UTILIZED, THE JACK SHALL INCORPORATE A TILTING MECHANISM THAT WILL ALLOW THE JACK HOUSING TO LEAN AWAY FROM THE TRUCK AND SHALL ALLOW ACCESS TO THE TRUCK POWER PLANT; WHEN VERTICAL, THE JACK SHALL BE SECURED IN POSITION BY A MINIMUM ONE (1) INCH DIAMETER PIN AND SHALL PIVOT ON A MINIMUM ONE (1) INCH DIAMETER PIN ROTARY DRIVE: SHALL BE PROVIDED WITH THE CAPACITY TO PRODUCE A MAXIMUM ROTATING FORCE OF NOT LESS THAN EIGHT THOUSAND (8,000) FOOT-POUNDS OF TORQUE; SHALL HAVE THE CAPACITY TO CREATE AND MAINTAIN A MAXIMUM ROTATION SPEED IN EXCESS OF FIVE HUNDRED FIFTY (550) RPM UNDER A LOADED CONDITION; SHALL HAVE AN INFINITELY ADJUSTABLE ROTATION SPEED CONTROL INCORPORATED INTO THE DRILLER'S CONTROL STATION AND SHALL ALLOW FOR SPEED SELECTIONS FROM ZERO (0) RPM TO MAXIMUM SPEED. VERTICAL DRIVE: SHALL BE ACTUATED BY DOUBLE-ACTING HYDRAULIC FEED CYLINDER(S); SHALL HAVE THE CAPACITY TO GENERATE A MAXIMUM RETRACT FORCE IN EXCESS OF TWENTY-FOUR THOUSAND (24,000) POUNDS AND A MAXIMUM DOWNWARD THRUST OF NOT LESS THAN FIFTEEN THOUSAND (15,000) POUNDS; SHALL HAVE A RAPID RETRACT FEATURE TO INCREASE THE VERTICAL RETRACT SPEED TO A MAXIMUM OF NOT LESS THAN EIGHTY-FIVE (85) FEET PER MINUTE UP AND NOT LESS THAN FIFTY- FIVE (55) FEET PER MINUTE DOWN; SHALL HAVE A PROVEN PRODUCTIVE METHOD OF UTILIZING AND DELIVERING A MAXIMUM OF NOT LESS THAN TEN-FOOT (10-FOOT) DRILL ROD LENGTHS WITH A MAXIMUM OUTSIDE DIAMETER OF NOT LESS THAN FOUR-AND-ONE-HALF (4 +) INCHES. DRILLER CONTROL STATION: ALL CONTROLS AND GAUGES NEEDED FOR VARIOUS DRILLING OPERATIONS SHALL BE PLACED IN SUCH A MANNER THAT SHALL BE EASILY ACCESSIBLE AND CONVENIENT FOR THE DRILL OPERATOR WHILE PERMITTING A VIEW OF THE DRILLING OPERATION AT ALL TIMES; DRILLER'S CONTROL PANEL SHALL BE MOUNTED ON THE REAR OF THE DRILL AND SHALL INCLUDE THE FOLLOWING INSTRUMENTATION AND CONTROLS: A METHOD (KEYED IGNITION, PUSH BUTTON, ETC ) OF STARTING THE POWER SOURCE AND AN ELECTRICALLY CONTROLLED ENGINE THROTTLE ON THE DRILL RIG CONTROL PANEL, PUSH-BUTTON EMERGENCY ENGINE SHUT-OFF SWITCH; GAUGES: HOUR METER, ENGINE OIL PRESSURE, ENGINE COOLANT TEMPERATURE AND VOLT METER; HYDRAULIC GAUGES FOR SYSTEM PRESSURE PULL-DOWN AND HOLD BACK PRESSURE; FEED RATE AND FEED PULL-DOWN PRESSURE CONTROL; FEED AND DETENTED FEED LEVERS AND HYDRAULIC CONTROLS FOR ALL STANDARD AND PROVIDED OPTIONAL COMPONENTS; DRILL CONTROLS SHALL BE ARRANGED IN GROUPS AND SITUATED FOR CONVENIENCE ACCORDING TO FREQUENCY OF USE AND FOR SAFETY AND CONVENIENCE; THE HYDRAULIC LEVERS SHALL HAVE DIRECTIONAL CONTROLS THAT CORRESPOND WITH CYLINDER MOVEMENT SAFETY AND EMERGENCY SHUT-DOWN SYSTEM: PUSH-BUTTON EMERGENCY SHUT-OFF SWITCHES SHALL BE LOCATED ON THE CONTROL PANEL AND SHALL BE WHERE NEEDED AT STRATEGIC LOCATIONS ON THE MAIN DRILL FRAME; A MINIMUM OF TWO (2) EMERGENCY SHUT-OFF SWITCHES SHALL BE LOCATED AT STRATEGIC LOCATIONS NEAR THE WORK AREA AND SHALL ASSURE AN IMMEDIATE STOP OF MOVEMENT AND ROTATION OF ALL MACHINERY IF TRIGGERED BY AN EMERGENCY SITUATION DRAW WORKS: SHALL INCLUDE TWO (2) HYDRAULICALLY POWERED LIFTING HOISTS AND A WIRELINE HOIST; THE FIRST HYDRAULIC HOIST SHALL HAVE A MAXIMUM PULLING CAPACITY OF NOT LESS THAN TWELVE THOUSAND (12,000) POUNDS; MAXIMUM LINE SPEED UP SHALL BE NOT LESS THAN SIXTY (60) FEET PER MINUTE; ONE HYDRAULIC LEVER SHALL BE FURNISHED FOR CONTROLLING DIRECTIONAL TRAVEL (HOISTING OR LOWERING) AND CABLE-DRUM ROTATION SPEED; HOIST SHALL BE ALIGNED IN SUCH A CONFIGURATION THAT THE WIRE ROPE SHALL BE CENTERED OVER THE DRILL HOLE AS IT EXITS THE CROWN SHEAVE; A HYDRAULIC BRAKE RELEASE VALVE SHALL BE FURNISHED THAT PERMITS WIRE ROPE TO LEAD OFF THE DRUM WHEN THE HOIST CONTROL LEVER IS POSITIONED TO SUSPEND A LOAD; HOIST SHALL INCLUDE AT LEAST SIXTY-FIVE (65) FEET OF ONE-HALF (+) INCH DIAMETER WIRE ROPE AND A SHUR-LOK HOOK (OR APPROVED EQUIVALENT) AND A CABLE GUIDE SHALL BE INCLUDED; THE SECOND HYDRAULIC HOIST SHALL HAVE A MAXIMUM PULLING CAPACITY OF NOT LESS THAN THIRTY TWO HUNDRED (3,200) POUNDS; MAXIMUM LINE SPEED SHALL BE NOT LESS THAN ONE HUNDRED (100) FEET PER MINUTE; A JIB SHALL BE FURNISHED AT THE UPPER PORTION OF THE MAST AND ALIGN WITH THIS HOIST; THE JIB SHALL BE HYDRAULICALLY ACTUATED TO SWIVEL AND EXTEND; ONE HYDRAULIC LEVER SHALL BE FURNISHED FOR CONTROLLING DIRECTION OF TRAVEL (HOISTING OR LOWERING) AND CABLE-DRUM ROTATION SPEED; THE HOIST SHALL INCLUDE AT LEAST SIXTY (60) FEET OF THREE-EIGHTHS (3/8) INCH DIAMETER WIRE ROPE WITH A SHUR-LOK HOOK (OR APPROVED EQUIVALENT) AND A CABLE GUIDE SHALL BE INCLUDED; THE HYDRAULIC WIRELINE HOIST SHALL HAVE A MAXIMUM PULLING CAPACITY OF NOT LESS THAN NINE HUNDRED (900) POUNDS; MAXIMUM LINE SPEED SHALL BE NOT LESS THAN FOUR HUNDRED (400) FEET PER MINUTE; ONE HYDRAULIC LEVER SHALL BE FURNISHED FOR CONTROLLING DIRECTION OF TRAVEL (HOISTING OR LOWERING) AND CABLE-DRUM ROTATION SPEED; THE HOIST SHALL BE CAPABLE OF HOLDING UP TO ONE THOUSAND SIX HUNDRED (1,600) FEET OF THREE-SIXTEENTHS (3/16) INCH DIAMETER WIRELINE CABLE. HYDRAULIC BREAKOUT DEVICES: SHALL BE INSTALLED WITH THE CAPABILITY OF HOLDING SECURELY DRILL ROD OR CORE TOOLING OF ALL SIZES UP TO AND INCLUDING FIVE (5) INCHES IN DIAMETER; SHALL BE CONSTRUCTED TO WITHSTAND LOADS, STRESS AND IMPACT ASSOCIATED WITH NORMAL USE OF UP TO ELEVEN (11) INCH DOWN-THE-HOLE AIR HAMMER AND ONE THOUSAND (1,000) FEET OF FOUR-AND-ONE-HALF (4 +) INCH DRILL ROD; CONFIGURED TO ALLOW FOR SAFE PERFORMANCE OF OTHER OPERATIONS WHILE THIS DEVICE IS NOT IN USE; HYDRAULICALLY OPERATED PIPE WRENCH SHALL BE INSTALLED TO OPERATE IN CONJUNCTION WITH THE HYDRAULIC HOLDING DEVICE STANDPIPE WITH HOSE TO CONTROL PANEL: A TWO (2) INCH DIAMETER STANDPIPE SHALL BE PROVIDED ON THE UPRIGHT FRAME (MAST) AND CONNECTED TO THE DRILL HEAD OR WATER SWIVEL BY HIGH PRESSURE HOSE; PROVISIONS SHALL BE MADE TO CONNECT THE OPPOSITE END OF THE STANDPIPE TO THE COMPRESSOR, GROUT PUMP OR MUD PUMP; PROVISIONS SHALL BE MADE FOR WATER INJECTION WHILE COMPRESSOR IS IN OPERATION; A PRESSURE RELEASE VALVE SHALL BE FURNISHED TO RELIEVE PRESSURE FROM THE PIPING WHILE BREAKING CONNECTIONS AND ADDING DRILL PIPE; PROVISIONS SHALL BE MADE TO CONNECT THESE DEVICES TO THE CONTROL PANEL GAUGES FOR MONITORING FROM THE DRILLER'S STATION WATER TANK/TOOL BOX ASSEMBLY: A WATER TANK/TOOL BOX COMBINATION SHALL BE PROVIDED; SHALL CONSIST OF A WATER COMPARTMENT THAT HAS THE CAPACITY TO HOLD A MAXIMUM OF NOT LESS THAN TWO HUNDRED FIFTY (250) GALLONS OF LIQUID; A TOOL COMPARTMENT AT BOTH ENDS OF THE WATER TANK WITH A MAXIMUM DEPTH OF NOT LESS THAN TWENTY-FOUR (24) INCHES; IF THE WATER TANK/TOOLBOX COMBINATION IS CONSTRUCTED OF STEEL IT SHALL BE FURNISHED WITH A RUST-PREVENTATIVE COATING APPLIED; HAVE BAFFLES INTEGRATED INSIDE TO PREVENT WATER SURGE; THE TOOLBOXES SHALL HAVE LOCKABLE DOORS AND OTHER CONFIGURATIONS WILL BE CONSIDERED OR ACCEPTED UPON APPROVAL. WATER INJECTION SYSTEM: A RECIPROCATING PUMP SHALL BE PROVIDED WITH NOT LESS THAN THREE (3) CYLINDERS; PUMP SHALL HAVE REPLACEABLE CERAMIC SLEEVES; PUMP SHALL BE CAPABLE OF PRODUCING A MAXIMUM LIQUID PRESSURE OF NOT LESS THAN EIGHT HUNDRED (800) PSI AND A MAXIMUM VOLUME OF NOT LESS THAN THIRTY-FIVE (35) GALLONS PER MINUTE OFF HOLE CAPABILITIES: A MECHANISM SHALL BE PROVIDED THAT ALLOWS FOR REPOSITIONING THE DRILL SPINDLE AND WIRELINE RETRIEVAL SYSTEM DURING CORING OPERATIONS WITHOUT REPOSITIONING THE DRILL TRUCK E.G.; WIGGLETAIL, SLIDE BASE, SLIDE HEAD, ETC.
002	57800 - MISCELLANEOUS PRODUCTS
THE BIDDER SHALL CONFORM TO THE SPECIFICATIONS CONTAINED HEREIN. THE BIDDER SHALL SUBMIT FIRM FIXED PRICES FOR EACH ITEM THE BIDDER CHOOSES TO BID HEREIN. HOWEVER, IF THE BIDDER BIDS LINE ITEM 001, THE BIDDER MUST BID LINE ITEM 002 AND IF THE BIDDER BIDS LINE ITEM 003, THE BIDDER MUST BID LINE ITEM 004. LINE ITEM 005 IS A STAND ALONE LINE ITEM THAT INCLUDES BOTH THE DRILL RIG AND THE TRUCK. ALL PRICES QUOTED SHALL BE CONSIDERED FIRM AND FIXED. TRUCK FOR DRILL RIG SPECIFIED IN LINE ITEM 001 FIRM, FIXED PRICE FOR TRUCK: SHALL INCLUDE ALL COMPONENTS AND MATERIALS WHICH ARE NECESSARY FOR THE TRUCK TO BE FULLY OPERATIONAL IN ACCORDANCE WITH THE SPECIFICATIONS STATED HEREIN BIDDER SHOULD COMPLETE EXHIBIT B DETAILING THE TRUCK BID FOR LINE ITEM 002. TRUCK: SHALL BE COMPATIBLE AND FULLY OPERATIONAL WITH THE DRILL RIG BID FOR LINE ITEM 001; SHALL BE MANUFACTURED WITH A LOAD CAPACITY NEEDED TO SUPPORT THE DRILL RIG BID IN LINE ITEM 001, BUT A GVW RATING OF NOT LESS THAN THIRTY-THREE THOUSAND (33,000) POUNDS; SHALL BE EQUIPPED WITH A DIESEL BURNING POWER PLANT THAT PRODUCES NOT LESS THAN TWO HUNDRED SIXTY (260) HORSEPOWER; SHALL HAVE A DIFFERENTIAL GEAR RATIO ADEQUATE WHEN COUPLED WITH THE TRANSMISSION TO PROPEL THE TRUCK AT HIGHWAY SPEEDS YET PRODUCE AMPLE TORQUE TO TURN THE WHEELS IN SOFT OFF-ROAD TERRAIN CONDITIONS; SHALL BE EQUIPPED WITH AN AIR BRAKE SYSTEM WITH ABS BRAKES; SHALL BE EQUIPPED WITH AN ENGINE BLOCK HEATER; SHALL BE EQUIPPED WITH HEAT/AC; SHALL BE EQUIPPED WITH AN AM/FM STEREO RADIO; SHALL BE EQUIPPED WITH AIR RIDE DRIVER SEAT AND PASSENGER SIDE SEATING; IN ADDITION TO THE ABOVE REQUIRED MANDATORY EQUIPMENT, THE TRUCK SHALL BE EQUIPPED WITH ALL STANDARD EQUIPMENT FOR THE MODEL SPECIFIED.
003	57800 - MISCELLANEOUS PRODUCTS
DRILL RIG POWERED BY TRUCK ENGINE POWER-TAKE-OFF (PTO) FIRM, FIXED PRICE FOR DRILL RIG: SHALL INCLUDE ALL COMPONENTS AND MATERIALS WHICH ARE NECESSARY FOR THE DRILL RIG TO BE FULLY OPERATIONAL IN ACCORDANCE WITH THE SPECIFICATIONS STATED HEREIN, SHALL INCLUDE INSTALLATION AND MOUNTING OF DRILL RIG TO THE TRUCK. THE BIDDER SHALL BID LINE ITEM 004 IF BIDDING LINE ITEM 003. BIDDER SHOULD COMPLETE EXHIBIT C DETAILING THE DRILL RIG BID FOR LINE ITEM 003. DRILL RIG SHALL MEET SAME SPECIFICATIONS/REQUIREMENTS AS STATED IN LINE ITEM 001 BUT WITH THE EXCEPTION OF THE FOLLOWING: DRILL POWER UNIT: POWER-TAKE-OFF (PTO) DRIVE SYSTEM FROM DIESEL TRUCK ENGINE TO THE DRILLING MACHINE; DRILL RIG SHALL NOT HAVE A SEPARATE POWER UNIT AND SHALL BE FULLY OPERATIONAL OFF OF THE TRUCK PTO.
004	57800 - MISCELLANEOUS PRODUCTS
TRUCK FOR DRILL RIG SPECIFIED IN LINE ITEM 003 FIRM, FIXED PRICE FOR TRUCK: SHALL INCLUDE ALL COMPONENTS AND MATERIALS WHICH ARE NECESSARY FOR THE TRUCK TO BE FULLY OPERATIONAL IN ACCORDANCE WITH THE SPECIFICATIONS STATED HEREIN BIDDER SHOULD COMPLETE EXHIBIT D DETAILING THE TRUCK BID FOR LINE ITEM 004. TRUCK: SHALL BE COMPATIBLE AND FULLY OPERATIONAL WITH THE DRILL RIG BID FOR LINE ITEM 003; SHALL BE MANUFACTURED WITH A LOAD CAPACITY NEEDED TO SUPPORT THE DRILL RIG BID IN LINE ITEM 003, BUT A GVW RATING OF NOT LESS THAN THIRTY-THREE THOUSAND (33,000) POUNDS; SHALL BE EQUIPPED WITH A DIESEL BURNING POWER PLANT THAT PRODUCES SUFFICIENT POWER TO OPERATE THE DRILL RIG BID IN LINE ITEM 003, BUT NOT LESS THAN TWO HUNDRED SIXTY (260) HORSEPOWER; SHALL HAVE A DIFFERENTIAL GEAR RATIO ADEQUATE WHEN COUPLED WITH THE TRANSMISSION TO PROPEL THE TRUCK AT HIGHWAY SPEEDS YET PRODUCE AMPLE TORQUE TO TURN THE WHEELS IN SOFT OFF-ROAD TERRAIN CONDITIONS; SHALL BE EQUIPPED WITH AN AIR BRAKE SYSTEM WITH ABS BRAKES; SHALL BE EQUIPPED WITH AN ENGINE BLOCK HEATER; SHALL BE EQUIPPED WITH HEAT/AC; SHALL BE EQUIPPED WITH AN AM/FM STEREO RADIO; SHALL BE EQUIPPED WITH AIR RIDE DRIVER SEAT AND PASSENGER SIDE SEATING; IN ADDITION TO THE ABOVE REQUIRED MANDATORY EQUIPMENT, THE TRUCK SHALL BE EQUIPPED WITH ALL STANDARD EQUIPMENT FOR THE MODEL SPECIFIED.
005	57800 - MISCELLANEOUS PRODUCTS
SMALLER CAPACITY DRILL RIG AND TRUCK DRILL RIG AND TRUCK: SHALL INCLUDE ALL COMPONENTS AND MATERIALS WHICH ARE NECESSARY FOR THE DRILL RIG AND TRUCK TO BE FULLY OPERATIONAL IN ACCORDANCE WITH THE SPECIFICATIONS STATED HEREIN, SHALL INCLUDE INSTALLATION AND MOUNTING OF DRILL RIG TO THE TRUCK. BIDDER SHOULD COMPLETE EXHIBIT E DETAILING THE DRILL RIG BID FOR LINE ITEM 001. DRILL RIG: SHALL BE CAPABLE OF PERFORMING AUGER BORING IN UNCONSOLIDATED FORMATIONS UTILIZING VARIOUS INDUSTRY STANDARD SIZE HOLLOW-STEM AUGERS (HSA) AND CAPABLE OF DRILLING TO AT LEAST FIFTY (50) FEET IN DEPTH WITH INDUSTRY STANDARD FOUR AND ONE QUARTER (4.25) INCH INSIDE DIAMETER (ID) HSA; SHALL BE CAPABLE OF UTILIZING DOWN-THE-HOLE AIR HAMMER TECHNOLOGY WITH THE USE OF UP TO A MINIMUM FOUR-AND-ONE-HALF (4.5) INCH OUTSIDE DIAMETER (OD) DRILL ROD WITH UP TO MINIMUM LENGTH OF TEN (10) FEET AND AN AUXILIARY AIR COMPRESSOR; SHALL BE CAPABLE OF CORING APPLICATIONS TO A MINIMUM DEPTH OF FIVE HUNDRED (500) FEET AND SHALL HAVE THE ROTATIONAL SPEED TO PRODUCTIVELY UTILIZE AQ CORE TOOLING AS SPECIFIED IN THE SECTION FOR THE ROTARY DRIVE; COMPONENT PARTS OF THE DRILL RIG SHALL BE OF PROPER SIZE AND DESIGN TO SAFELY WITHSTAND MAXIMUM STRESSES IMPOSED BY A CAPACITY LOAD; SHALL HAVE ALL MANUFACTURERS' RECOMMENDED LUBRICATION FITTINGS; SHALL UTILIZE PARTS AND COMPONENTS SUCH AS CHAINS, BEARINGS AND UNIVERSAL JOINTS WITH MANUFACTURER'S RATINGS EXCEEDING THE LOADS AND STRESS PLACED ON THEM WHILE UNDER USE AT CAPACITY LOADS AS SPECIFIED HEREIN; SHALL HAVE A PRIMER UNDER COAT TO RETARD THE CORROSION AND PROTECT THE METAL AND A TOP COAT OF PAINT IN COLORS SPECIFIED BY THE STATE AGENCY. DRILL PLATFORM: THE DRILL PLATFORM SHALL BE CONSTRUCTED FROM A STEEL SLIP RESISTANT DECK PLATE OF SUFFICIENT STRENGTH AND THICKNESS TO WITHSTAND NORMAL WEAR AND LOADING; DRILL ROD AND AUGER RACKS SHALL BE FURNISHED; CLEARANCE LIGHTS SHALL BE INCLUDED; THE PLATFORM WIDTH SHALL NOT EXCEED A MAXIMUM OF NINETY-SIX (96) INCHES; A DRILLER'S STEP/STAND SHALL BE PROVIDED AND STORED AT A CONVENIENT POSITION BELOW THE DRILLER'S CONTROL PANEL IF NEEDED TO CONVENIENTLY OPERATE CONTROLS ON THE CONTROL PANEL; THE DRILL PLATFORM SHALL BE UNDERCOATED FOR PROTECTION AGAINST CORROSION UPRIGHT DRILL FRAME: THE UPRIGHT DRILL FRAME SHALL BE HYDRAULICALLY ACTUATED ALLOWING FOLD OVER FOR TRANSPORT; DRILL FRAME SHALL BE CONTROLLED BY DOUBLE-ACTING HYDRAULIC CYLINDER(S); A RESTRICTION SHALL BE PROVIDED IN THE HYDRAULIC ROUTING SYSTEM TO PREVENT THE DRILL FRAME FROM FOLDING IN AN UNSAFE MANNER DUE TO AN UNEXPECTED EMERGENCY FAILURE SITUATION DRILL POWER UNIT: POWER-TAKE-OFF (PTO) DRIVE SYSTEM FROM DIESEL TRUCK ENGINE TO THE DRILLING MACHINE - OR - SHALL BE A DECK-MOUNTED, ELECTRIC START, HEAVY DUTY INDUSTRIAL TYPE, DIESEL ENGINE; SHALL BE EQUIPPED WITH A HEAVY-DUTY DRY TYPE REPLACEABLE ELEMENT AIR CLEANER WITH PRE-CLEANER; SHALL HAVE A FULL FLOW OIL FILTER; SHALL HAVE A MINIMUM TWELVE (12) VOLT ELECTRIC STARTING SYSTEM CONSISTING OF A STARTER, ALTERNATOR, BATTERY, REGULATOR; SHALL HAVE A METHOD OF STARTING THE POWER SOURCE AND AN ENGINE THROTTLE ON THE DRILL CONTROL PANEL; SHALL HAVE SUFFICIENT POWER TO MEET ALL REQUIREMENTS LISTED ELSEWHERE IN THIS SPECIFICATION; FUEL FOR THE POWER UNIT SHALL COME FROM THE TRUCK CARRIER FUEL TANKS HYDRAULIC SYSTEM: SHALL HAVE A HEAVY-DUTY, ENGINE DRIVEN HYDRAULIC PUMP WITH A MAXIMUM PRESSURE OF NOT LESS THAN TWO THOUSAND (2,000) PSI; SHALL BE EQUIPPED WITH A REPLACEABLE FULL FLOW ELEMENT HYDRAULIC OIL FILTER; A HYDRAULIC OIL COOLER SHALL BE FURNISHED AND THE HYDRAULIC OIL RESERVOIR SHALL HAVE ADEQUATE CAPACITY AND SHALL BE EQUIPPED WITH A VENTED FILLER CAP HYDRAULIC LEVELING JACKS: SHALL BE FURNISHED AND SHALL BE INDIVIDUALLY OPERATED FROM THE CONTROL PANEL AT THE REAR OF THE DRILL; SHALL PROVIDE ADEQUATE LEVELING CAPABILITY; SHALL BE STRONG AND RIGID ENOUGH AND SHALL EASILY SUPPORT THE TOTAL WEIGHT OF THE MACHINE PLUS THE LOAD GENERATED WHEN RETRACTING DRILLING TOOLS; CHECK VALVES SHALL BE FURNISHED IN THE HYDRAULIC LINES AND SHALL PREVENT LEAKAGE OR SLIPPAGE OF THE JACKS WHILE THE DRILL IS SET UP ON SITE; CHROME-PLATED JACK PISTON RODS SHALL BE COMPLETELY ENCLOSED TO SAFEGUARD THEM FROM DAMAGE AND FOOT PADS SHALL BE A MINIMUM OF TEN (10) INCHES DIAMETER; TWO (2) JACKS SHALL BE MOUNTED AT THE REAR OF THE PLATFORM, ONE (1) ON EACH CORNER, AND A MINIMUM OF ONE (1) AT THE FRONT OF THE TRUCK CARRIER OR DRILL PLATFORM ROTARY DRIVE: SHALL BE PROVIDED WITH THE CAPACITY TO PRODUCE A MAXIMUM ROTATING FORCE OF NOT LESS THAN SEVEN THOUSAND (7,000) FOOT-POUNDS OF TORQUE; SHALL HAVE THE CAPACITY TO CREATE AND MAINTAIN A MAXIMUM ROTATION SPEED IN EXCESS OF SIX HUNDRED TWENTY (620) RPM UNDER A LOADED CONDITION; SHALL HAVE AN INFINITELY ADJUSTABLE ROTATION SPEED CONTROL INCORPORATED INTO THE DRILLER'S CONTROL STATION AND SHALL ALLOW FOR SPEED SELECTIONS FROM ZERO (0) RPM TO MAXIMUM SPEED. VERTICAL DRIVE: SHALL BE ACTUATED BY DOUBLE-ACTING HYDRAULIC FEED CYLINDER(S); SHALL HAVE THE CAPACITY TO GENERATE A MAXIMUM RETRACT FORCE IN EXCESS OF TWELVE THOUSAND (12,000) POUNDS AND A MAXIMUM DOWNWARD THRUST OF NOT LESS THAN ELEVEN THOUSAND SEVEN HUNDRED (11,700) POUNDS; SHALL HAVE A RAPID RETRACT FEATURE TO INCREASE THE VERTICAL RETRACT SPEED; SHALL HAVE A PROVEN PRODUCTIVE METHOD OF UTILIZING AND DELIVERING A MAXIMUM OF NOT LESS THAN TEN FOOT (10-FOOT) DRILL ROD LENGTHS WITH A MAXIMUM OUTSIDE DIAMETER OF NOT LESS THAN FOUR-AND-ONE-HALF (4 +) INCHES. DRILLER CONTROL STATION: ALL CONTROLS AND GAUGES NEEDED FOR VARIOUS DRILLING OPERATIONS SHALL BE PLACED IN SUCH A MANNER THAT SHALL BE EASILY ACCESSIBLE AND CONVENIENT FOR THE DRILL OPERATOR WHILE PERMITTING A VIEW OF THE DRILLING OPERATION AT ALL TIMES; DRILLER'S CONTROL PANEL SHALL BE MOUNTED ON THE REAR OF THE DRILL AND SHALL INCLUDE THE FOLLOWING INSTRUMENTATION AND CONTROLS: A METHOD (KEYED IGNITION SWITCH, STARTER BUTTON, ETC.) OF STARTING THE POWER SOURCE AND AN ENGINE THROTTLE, PUSH-BUTTON EMERGENCY ENGINE SHUT-OFF SWITCH; GAUGES: HOUR METER, ENGINE OIL PRESSURE, ENGINE COOLANT TEMPERATURE AND VOLT METER; HYDRAULIC GAUGES FOR SYSTEM PRESSURE PULL-DOWN AND HOLD BACK PRESSURE; FEED RATE AND FEED PULL-DOWN PRESSURE CONTROL; FEED AND DETENTED FEED LEVERS AND HYDRAULIC CONTROLS FOR ALL STANDARD AND PROVIDED OPTIONAL COMPONENTS; DRILL CONTROLS SHALL BE ARRANGED IN GROUPS AND SITUATED FOR CONVENIENCE ACCORDING TO FREQUENCY OF USE AND FOR SAFETY AND CONVENIENCE; THE HYDRAULIC LEVERS SHALL HAVE DIRECTIONAL CONTROLS THAT CORRESPOND WITH FEED MOVEMENT SAFETY AND EMERGENCY SHUT-DOWN SYSTEM: PUSH-BUTTON EMERGENCY SHUT-OFF SWITCH SHALL BE LOCATED ON THE CONTROL PANEL; A MINIMUM OF TWO (2) EMERGENCY SHUT-OFF SWITCHES SHALL BE LOCATED AT STRATEGIC LOCATIONS NEAR THE WORK AREA AND SHALL ASSURE AN IMMEDIATE STOP OF MOVEMENT AND ROTATION OF ALL MACHINERY IF TRIGGERED BY AN EMERGENCY SITUATION DRAW WORKS: SHALL INCLUDE ONE (1) HYDRAULICALLY POWERED LIFTING HOIST AND ONE (1) WIRELINE HOIST; THE HYDRAULIC LIFTING HOIST SHALL HAVE A MAXIMUM PULLING CAPACITY OF NOT LESS THAN FOUR THOUSAND FIVE HUNDRED (4,500) POUNDS; MAXIMUM LINE SPEED UP SHALL BE NOT LESS THAN FORTY (40) FEET PER MINUTE; ONE HYDRAULIC LEVER SHALL BE FURNISHED FOR CONTROLLING DIRECTIONAL TRAVEL (HOISTING OR LOWERING) AND CABLE-DRUM ROTATION SPEED; HOIST SHALL BE ALIGNED IN SUCH A CONFIGURATION THAT THE WIRE ROPE SHALL BE CENTERED OVER THE DRILL HOLE AS IT EXITS THE CROWN SHEAVE; A HYDRAULIC BRAKE RELEASE VALVE SHALL BE FURNISHED THAT PERMITS WIRE ROPE TO LEAD OFF THE DRUM WHEN THE HOIST CONTROL LEVER IS POSITIONED TO SUSPEND A LOAD; HOIST SHALL INCLUDE AT LEAST SIXTY-FIVE (65) FEET OF ONE-HALF (+) INCH DIAMETER WIRE ROPE AND A SHUR-LOK HOOK (OR APPROVED EQUIVALENT) AND A CABLE GUIDE SHALL BE INCLUDED; THE HYDRAULIC WIRELINE HOIST SHALL HAVE A MAXIMUM PULLING CAPACITY OF NOT LESS THAN EIGHT HUNDRED (800) POUNDS; MAXIMUM LINE SPEED SHALL BE NOT LESS THAN ONE HUNDRED FORTY (140) FEET PER MINUTE; ONE HYDRAULIC LEVER SHALL BE FURNISHED FOR CONTROLLING DIRECTION OF TRAVEL (HOISTING OR LOWERING) AND CABLE-DRUM ROTATION SPEED; THE HOIST SHALL BE CAPABLE OF HOLDING UP TO FIVE HUNDRED (500) FEET OF THREE-SIXTEENTHS (3/16) INCH DIAMETER WIRELINE CABLE. HYDRAULIC BREAKOUT DEVICES: SHALL BE INSTALLED WITH THE CAPABILITY OF HOLDING SECURELY DRILL ROD OR CORE TOOLING OF ALL SIZES UP TO AND INCLUDING FOUR-AND-ONE-HALF (4.5) INCHES IN DIAMETER; SHALL BE CONSTRUCTED TO WITHSTAND LOADS AND STRESSES ASSOCIATED WITH NORMAL USE OF A DOWN-THE-HOLE AIR HAMMER AND FIVE HUNDRED (500) FEET OF FOUR-AND-ONE-HALF (4.5) INCH DRILL ROD; CONFIGURED TO ALLOW FOR SAFE PERFORMANCE OF OTHER OPERATIONS WHILE THIS DEVICE IS NOT IN USE; HYDRAULICALLY OPERATED PIPE WRENCH SHALL BE INSTALLED TO OPERATE IN CONJUNCTION WITH THE HOLDING DEVICE STANDPIPE WITH HOSE TO CONTROL PANEL: A TWO (2) INCH DIAMETER STANDPIPE SHALL BE PROVIDED ON THE UPRIGHT FRAME (MAST) AND CONNECTED TO THE DRILL HEAD OR WATER SWIVEL BY HIGH PRESSURE HOSE; PROVISIONS SHALL BE MADE TO CONNECT THE OPPOSITE END OF THE STANDPIPE TO THE COMPRESSOR, GROUT PUMP OR MUD PUMP; PROVISIONS SHALL BE MADE FOR WATER INJECTION WHILE COMPRESSOR IS IN OPERATION; A PRESSURE RELEASE VALVE SHALL BE FURNISHED TO RELIEVE PRESSURE FROM THE PIPING WHILE BREAKING CONNECTIONS AND ADDING DRILL PIPE; PROVISIONS SHALL BE MADE TO CONNECT THESE DEVICES TO THE CONTROL PANEL GAUGES FOR MONITORING FROM THE DRILLER'S STATION TOOL BOX ASSEMBLY: A MINIMUM OF ONE (1) TOOL BOX SHALL BE PROVIDED THAT IS PERMANENTLY ATTACHED TO THE TRUCK OR DRILL PLATFORM; THE TOOL COMPARTMENT MAY BE ATTACHED ABOVE OR BELOW THE DECK; THE TOOL BOX(ES) MUST HAVE MINIMUM DIMENSIONS OF EIGHTEEN (18) INCHES BY EIGHTEEN (18) INCHES BY THIRTY-SIX (36) INCHES OR COMPARABLE; IF THE TOOL BOX(ES) IS CONSTRUCTED OF STEEL IT SHALL BE FURNISHED WITH A RUST-PREVENTATIVE COATING APPLIED; THE TOOL BOX(ES) SHALL HAVE LOCKABLE DOORS AND OTHER CONFIGURATIONS WILL BE CONSIDERED OR ACCEPTED UPON APPROVAL AUGER RACK: A MINIMUM OF ONE (1) AUGER RACK SHALL BE PROVIDED FOR THE STORAGE AND TRANSPORT OF INDUSTRY-STANDARD FIVE-FOOT (5-FT) LONG AUGERS; THE AUGER RACK MAY BE ATTACHED ABOVE OR BELOW THE DRILL PLATFORM; THE RACK MUST BE CONSTRUCTED IN SUCH A WAY THAT AUGERS CAN BE SECURED FOR SAFE TRANSPORT AT HIGHWAY SPEEDS WATER INJECTION SYSTEM: A RECIPROCATING PUMP SHALL BE PROVIDED; PUMP SHALL HAVE REPLACEABLE SLEEVES; PUMP SHALL BE CAPABLE OF PRODUCING A MAXIMUM LIQUID PRESSURE OF NOT LESS THAN FIVE HUNDRED (500) PSI AND A MAXIMUM VOLUME OF NOT LESS THAN EIGHTEEN (18) GALLONS PER MINUTE OFF HOLE CAPABILITIES: A MECHANISM SHALL BE PROVIDED THAT ALLOWS FOR REPOSITIONING THE DRILL SPINDLE AND WIRELINE RETRIEVAL SYSTEM DURING CORING OPERATIONS WITHOUT REPOSITIONING THE DRILL TRUCK E.G.; WIGGLETAIL, SLIDE BASE, SLIDE HEAD, ETC. TRUCK: SHALL BE COMPATIBLE AND FULLY OPERATIONAL WITH THE DRILL RIG AND ACCESSORIES SPECIFIED ABOVE; SHALL BE MANUFACTURED WITH A GVW RATING SUFFICIENT TO LEGALLY AND SAFELY CARRY ITEMS STATED ABOVE; SHALL BE EQUIPPED WITH A DIESEL BURNING POWER PLANT THAT PRODUCES SUFFICIENT HORSEPOWER TO POWER THE DRILL IF DRIVEN BY A POWER-TAKE-OFF (PTO); SHALL BE PROVIDED WITH FOUR-WHEEL DRIVE (4WD) CAPABILITY; SHALL BE PROVIDED WITH A DIFFERENTIAL GEAR RATIO ADEQUATE WHEN COUPLED WITH THE TRANSMISSION TO PROPEL THE TRUCK AT HIGHWAY SPEEDS YET PRODUCE AMPLE TORQUE TO TURN THE WHEELS IN SOFT OFF-ROAD TERRAIN CONDITIONS; SHALL BE EQUIPPED WITH AN ENGINE BLOCK HEATER; SHALL BE PROVIDED WITH A SPARE TIRE OF THE SAME SIZE AND RATING AS THE OTHER TIRES AND SECURED ON A MOUNTING BRACKET; SHALL BE EQUIPPED WITH HEAT/AC; SHALL BE EQUIPPED WITH AN AM/FM STEREO RADIO; IN ADDITION TO THE ABOVE REQUIRED MANDATORY EQUIPMENT, THE TRUCK SHALL BE EQUIPPED WITH ALL STANDARD EQUIPMENT FOR THE MODEL SPECIFIED DELIVERY: THE CONTRACTOR SHALL DELIVER THE DRILL RIG AND TRUCK BY JUNE 1, 2009. THE BIDDER SHOULD CONFIRM BELOW THE DELIVERY DATE OF THE DRILL RIG BID: DELIVERY: ______________________________ WARRANTY: THE BIDDER SHOULD STATE THE STANDARD MANUFACTURER'S WARRANTY FOR THE DRILL RIG AND THE TRUCK BID: WARRANTY: ______________________________________________________________________

For more information, please contact TURNER, CALE at cale.turner@oa.mo.gov